Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 11

Страница: 11 / 146

Chapter 1

Introduction

1-1 Overview

The SuperServer 2027PR-HTR/HTFR/HTTR is a high-end server comprised

of two main subsystems: the -R2K02B 2U server chassis and the

X9DRT-P/PIBF/PT dual processor serverboard. Please refer to our web site for

information on operating systems that have been certifi ed for use with the system

(

www.supermicro.com

In addition to the serverboard and chassis, various hardware components have been

included with the 2027PR-HTR/HTFR/HTTR server, as listed below:

•

Four (4) Mylar air shrouds for TwinPro -R2K02B X10

(MCP-310-21702-0B)

•

Four (4) 80x80x38mm 13.8K RPM chassis middle fan (FAN-0136L4)

•

Heat Sinks

Four (4) 1U passive CPU heat sinks for rear CPU (SNK-P0047PSM)

Four (4) 1U passive CPU heat sinks w/narrow ILM (SNK-P0057PS)

•

One (1) Power Distributor Board (PDB-PT217-S2412)

•

SATA Backplane:

One (1) Twin square backplane, supporting 24 SATA3 HDD (2.5") with hot

swapping (BPN-SAS3-217HQ)

Four (4) TwinPro backplane adapter cards, each w/6 SATA ports

(BPN-ADP-6SATA3P-O-P)

Twenty-four (24) hot-swap 2.5" HDD trays (MCP-220-00047-0B)

•

Four (4) Riser cards (RSC-R1UTP-E16R)

•

One (1) rails set (MCP-290-00053-0N)

Note:

For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

•

Supermicro product manuals:

http://www.supermicro.com/support/manuals/

•

Product drivers and utilities:

ftp://ftp.supermicro.com

•

Product safety information:

http://super-dev/about/policies/safety_information.cfm

•

If you have any questions, please contact our support team at:

[email protected]

Chapter 1: Introduction

1-1

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды