Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 66

Страница: 66 / 146

5-12

SUPERSERVER 2027PR-HTR/HTFR/HTTR USER'S MANUAL

Installing LRDIMM (ECC) Memory

Intel E5-2600(V2) Series Processor LRDIMM Memory

Support

Ranks

Per DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note Below)

Speed (MT/s) and Voltage

Validated by Slot per Channel

(SPC) and DIMM Per Channel

(DPC)

1 Slot Per

Channel

2 Slots Per

Channel

1DPC

1DPC and

2DPC

1.35V

1.5V

1.35V

1.5V

QRx4

(DDP)

16GB

32GB

1066,
1333,

1600

1066,
1333,

1600

1066,

1333

1066,

1333

QRx8 (P)

8GB

16GB

1066,
1333,

1600

1066,
1333,

1600

1066,

1333

1066,

1333

Note:

For detailed information on memory support and updates, please refer to the

SMC Recommended Memory List posted on our website at http://www.supermicro.
com/support/resources/mem.cfm.

Other Important Notes and Restrictions

•

For the memory modules to work properly, please install DIMM modules of the

same type, same speed and same operating frequency on the motherboard.

Mixing of RDIMMs, UDIMMs or LRDIMMs is not allowed. Do not install both

ECC and Non-ECC memory modules on the same motherboard.

•

Using DDR3 DIMMs with different operating frequencies is not allowed. All

channels in a system will run at the lowest common frequency.

5-6 Adding PCI Expansion Cards

The 2027PR-HTR/HTFR/HTTR includes four preinstalled riser cards (one per node)

designed specifi cally for use in the -R2K02B 2U rackmount chassis.

These riser cards support low-profi le PCI Express x16 cards to fi t inside the chassis.

Installing an Expansion Card

1. After powering down the system, remove the PCI slot shield.

2. Fully seat the card into the slot, pushing down with your thumbs evenly on

both sides of the card.

3. Finish by using a screw to secure the top of the card shield to the chassis.

The PCI slot shield protects the motherboard and its components from EMI

and aid in proper ventilation, so make sure it is always in place.

Note:

See Chapter 6 for more installation details.

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды