Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 121

Страница: 121 / 146

Chapter 7: BIOS

7-17

Port 0 ~ Port 5 Spin Up Device

On an edge detect from 0 to 1, set this item to allow the PCH to start a

COMRESET initialization sequence to the device. The options are Enabled and

Disabled

Port 0~5 Staggered Spin Up

Select Enabled to enable Staggered Spin-up support to prevent excessive

power consumption caused by multiple HDDs spinning-up simultaneously.

The options are Enabled and

Disabled

RAID Mode

The following items are displayed when RAID Mode is selected:

PCH RAID CodeBase

Select Intel.to confi gure RAID settings using the Intel PCH controller. Select

LSI to confi gure RAID settings using the LSI controller. The options are

Intel

and LSI.

SATA RAID Option ROM/UEFI Driver (Available if the item above -
SATA Mode Select is set to AHCI or RAID)

Select Enabled to use the SATA RAID Option ROM/UEFI driver for system

boot. The options are

Enabled

and Disabled.

Port 0~5 Hot Plug

Select Enabled to enable hot-plug support for the particular port. The options

are

Enabled

and Disabled.



SCU (System Confi guration Unit) Confi guration

Storage Control Unit

Select Enabled to support Intel PCH devices. The options are Disabled and

Enabled

SATA RAID Option ROM/UEFI Driver

Select Enabled to use the SATA RAID Option ROM/UEFI driver for system boot.

The options are

Enabled

and Disabled.

SCU Devices

Select Enabled to enable support for PCH SCU (System Confi guration Utility)

devices. The options are Disabled and

Enabled

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды