Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 57

Страница: 57 / 146

Chapter 5: Advanced Serverboard Setup

5-3

5-4 Processor and Heatsink Installation

Notes:

•

Always remove the power cord before adding, removing or changing a CPU.

•

When receiving a serverboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;

otherwise, contact your retailer immediately.

•

If you buy a CPU separately, use only an Intel-certifi ed, multi-directional heatsink.

•

Avoid placing direct pressure to the top of the processor package.

•

Install the processor into the CPU socket before installing the heatsink.

•

Refer to the Supermicro web site for updates on CPU support.

Release the lever

labeled "Open 1st"

Installing a CPU

1. There are two levers on the LGA

2011 socket. First press and

release the load lever labeled

"Open 1st".

OPEN 1st

OPEN

1st

OPEN 1st

OPEN

1st

Release the lever

labeled "Close 1st"

2. Press the second load lever

labeled "Close 1st" to release the

load plate from its locked position.

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды