Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 76

Страница: 76 / 146

5-22

SUPERSERVER 2027PR-HTR/HTFR/HTTR USER'S MANUAL

Infi niBand Enable (JIB1)

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Enabled (Default)

Pins 2-3

Disabled

I2C to PCI-E (JI

C1/JI

C2)

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Enabled

Pins 2-3

Disabled (Default)

ME Recovery (JPME1)

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Normal (Default)

Pins 2-3

ME Recovery

ME Mode Select (JPME2)

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Normal (Default)

Pins 2-3

Manufacture Mode

Infi niBand (IB) Enable

Jumper JIB1 allows the user to enable

the onboard Infi niBand connector for

the X9DRT-PIBF serverboard. The

default setting is 1-2 to enable the

connection. See the table on the right

for jumper settings.

Manufacture Mode Select

Close Pin 2 and Pin 3 of Jumper

JPME2 to bypass SPI fl ash security

and force the system to operate in

the Manufacture Mode, allowing the

user to flash the system firmware

from a host server for system setting

modifi cations. See the table on the

right for jumper settings.

I2C Bus to PCI-Exp. Slots

Jumpers JI

C1 and JI

C2 allow you

to connect the System Management

Bus (I

C) to PCI-Express slots. The

default setting is Open to disable the

connection. See the table on the right

for jumper settings.

Management Engine (ME)

Recovery

Use Jumper JPME1 to select ME

Firmware Recovery mode, which will

limit resource allocation for essential

system operation only in order to

maintain normal power operation and

management. In the single operation

mode, online upgrade will be available

via Recovery mode. See the table on

the right for jumper settings.

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды