Supermicro Supero SUPERSERVER 2027PR-HTFR Скачать руководство пользователя страница 86

Страница: 86 / 146

6-2

SUPERSERVER 2027PR-HTR/HTFR/HTTR USER'S MANUAL

6-2 Removing the Power Cord

1. Use the operating system to power down the node, following the on-screen

prompts.

2. After the system has completely shut-down, carefully grasp the head of the

power cord and gently pull it out of the back of the power supply.

3. If your system has dual power supplies, remove the cords from both power

supplies.

4. Disconnect the cord from the power strip or wall outlet.

6-3 Control

Panel

The control panel is located on the front of the chassis. The LEDs inform you of

system status.

See Chapter 3 for details on the LEDs and the control panel buttons.

Figure 6-1. Front and Rear Chassis Views

SATA Drives (24)

Control Panel

Ethernet Ports

USB Ports

VGA Port

IPMI LAN Port

Infi niband Port

(X9DRT-PIBF only)

PCI-E Slot

Содержание Supero SUPERSERVER 2027PR-HTFR



















































































































































Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды

Supermicro Supero SUPERSERVER 2027PR-HTFR, Руководство пользователя

Результаты поиска

Содержание Supero SUPERSERVER 2027PR-HTFR

Отзывы:

Похожие инструкции для Supero SUPERSERVER 2027PR-HTFR

Бренды по названию

Популярные бренды