SunFounder Q250 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 50

background image

11

Plug in the CC3D Flight Control

Connect the CC3D flight controller to computer with the Micro USB Cable included, and
you can see the

Power LED

lights up and stay brighten constantly, while the

Status LED

blinks.

The driver installation will take some minutes; a reminder of failing to install may pop up as
shown below, and you can just ignore it - the installation result in

Device Manager

shall

prevail.

Open

Device Manager

. If you see

CopterControl Virtual COM Port (COMxx)

(the number

depends on your actual situation), it indicates the flight controller has been recognized by
the computer.

If

you see the

CopterControl

with a yellow exclamation mark

！

in

Other devices

:

SunFounder

«
...
11
12
13
14
15
...
»

Содержание Q250



















































Отзывы:

Нет отзывов

Похожие инструкции для Q250

Бренд: Abusemark Страницы: 4

Бренд: Traxxas Страницы: 4

Бренд: Quer Страницы: 72

Бренд: Quadrone Страницы: 11

Бренд: udir/c Страницы: 6

Upgrade U818A HD

Бренд: UDI RC Страницы: 10

Бренд: udir/c Страницы: 16

Бренд: UDI RC Страницы: 11

Бренд: UDI R/C Страницы: 12

Бренд: Aovo Страницы: 38

Бренд: Xaircraft Страницы: 13

Бренд: FyeTech Страницы: 27

Бренд: RCTECH Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды