SunFounder Q250 Скачать руководство пользователя | Manualshive

Страница: 36 / 50

background image

34

Click

Input

, and set the

Min

,

Neutral

and

Max

values for all channels.

Min

: the minimum value of the channel.

Neutral

: the threshold value of the channel. The Neutral for throttle should be set greater

than that for four motors (1089), and about 50 greater than the

Min

value, in case the

aircraft takes off when we just slightly pull the throttle; and it leaves enough throttle
ascending space, which would be easier to operate for entry-level hobbyists. Set all
others

Neutral

values to 1500 (median for Min and Max).

Max

: the maximum value of the channel.

SunFounder

«
...
34
35
36
37
38
...
»

Содержание Q250



















































Отзывы:

Нет отзывов

Похожие инструкции для Q250

AMPX FOC ESC 60A

Бренд: MAD Страницы: 2

AMPX ESC 40A HV

Бренд: MAD Страницы: 2

Бренд: GAUI Страницы: 30

SafeAir M-600 V2 Auto-ARM

Бренд: ParaZero Страницы: 37

Бренд: HeliBEST Страницы: 9

GRAVIT SMART VISION FPV

Бренд: LRP Страницы: 25

Folding Drone GPS 1668261

Бренд: Reely Страницы: 44

Бренд: Walkera Страницы: 28

Бренд: SkyHobbies Страницы: 3

Бренд: RCTECH Страницы: 8

Бренд: MiDRONE Страницы: 65

Бренд: LiteHawk Страницы: 20

Бренд: Crivit Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды