SunFounder Q250 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 50

background image

21

The output calibration means setting the neutral rate for the motor. Follow the steps below:

Step 1

: Connect the battery to the aircraft.

Step 2

: Press the

Start

button below and slide the slider to the right until the motor starts to

spin.

Step 3

:

Click

Stop

. When the motor stops, press

Start

again to see whether the motor can

start itself. Slide the sliders to the left or right to set the critical point of the motor to spin.

Step 4

:

Please pay attention to the rotation direction of the motor. Ensure the motors are

spinning in the correct direction as shown in the diagram. Otherwise, swap any two wires of
a motor to change the direction.

Since the output calibration of the Motor 2, 3 and 4 is the same as the Motor 1, just set their
neutral rate in the same way as setting the Motor 1.

Note

: Pay attention

NOT

to make the motor spin too slowly because it will give out much

heat at the critical point, which may damage the motor.

SunFounder

«
...
21
22
23
24
25
...
»

Содержание Q250



















































Отзывы:

Нет отзывов

Похожие инструкции для Q250

Бренд: REVELL Страницы: 22

AW-QDR-TBCAM Tumbler-Cam

Бренд: Quadrone Страницы: 8

Бренд: Toyabi Страницы: 8

Бренд: Aovo Страницы: 6

Бренд: Aovo Страницы: 6

Бренд: Vifly Страницы: 8

Бренд: Suntor Страницы: 12

Super Multi-Rotor Controller

Бренд: Hobby People Страницы: 4

Бренд: Hobby People Страницы: 24

Aerocraft CamQuad

Бренд: Hobby People Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды