SunFounder Q250 Скачать руководство пользователя | Manualshive

Страница: 43 / 50

background image

41

Step 9

: Click

Input

, and set the

Min

,

Neutral

and

Max

values for all channels.

Min:

the minimum value of the channel.

Neutral

: the threshold value of the channel. The Neutral for throttle should be set greater

than that for four motors (1088), and about 50 greater than the

Min

value, in case the

aircraft takes off when we just slightly pull the throttle; and it leaves enough throttle
ascending space, which would be easier to operate for entry-level hobbyists. Set all
others

Neutral

values to 1500 (median for Min and Max).

Max

: the maximum value of the channel.

Move the channel stick. If the channel value slider is toggled reversely, just tick

Reversed

.

For instance, when you move the Pitch stick from bottom to top, if the channel value slider
is toggled from right to left at the same time, it indicates it is reversed. Thus you should tick
the box

Reversed

after Pitch. Then click

Save

after modifying.

PPM Mode

Step 1

: Ensure the receiver has been toggled to the

PPM

mode and the receiver wiring has

been connected correctly, power on the aircraft and radio transmitter with a battery.

Step 2

: Open

OpenPilot

, and click

Input

at left side, then select

PPM

for all channels under

Type, and set Chan1 –Chan5 under

Number

correspondingly (

Throttle

,

Roll

,

Pitch

, and

Yaw

are main channels, while

FlightMode

are aux channel to set the flight mode. To realize basic

flight needs, we only need to set these 5 channels. Then click

Save

.

SunFounder

«
...
41
42
43
44
45
...
»

Содержание Q250



















































Отзывы:

Нет отзывов

Похожие инструкции для Q250

Бренд: ParaZero Страницы: 17

Бренд: GAUI Страницы: 30

SafeAir M-600 V2 Auto-ARM

Бренд: ParaZero Страницы: 37

Бренд: udir/c Страницы: 12

Бренд: Xaircraft Страницы: 18

Бренд: REVELL Страницы: 29

Бренд: SUPERNOVA Страницы: 5

Бренд: SKY-HERO Страницы: 19

Бренд: Kaiser Baas Страницы: 38

Бренд: Ares Страницы: 2

Бренд: HOBBYEAGLE Страницы: 16

Inspire 1 1345LS

Бренд: dji Страницы: 8

Motion Controller Combo

Бренд: dji Страницы: 17

Бренд: Air Hogs Страницы: 2

Бренд: REES52 Страницы: 27

Бренд: RunCam Страницы: 8

Бренд: RunCam Страницы: 10

NH90102 Pocket Cam

Бренд: NINCOAIR Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды