SunFounder Q250 страница 47 Скачать руководство пользователя

Страница: 47 / 50

Move the channel stick. If the channel value slider is toggled reversely, just tick

Reversed

For instance, when you move the Pitch stick from bottom to top, if the channel value slider
is toggled from right to left at the same time, it indicates it is reversed. Thus you should tick
the box

Reversed

after Pitch. Then click

Save

after modifying.

SBUS Mode

Step 1

: Ensure the receiver has been toggled to the

SBUS

mode and the receiver wiring

has been connected correctly, power on the aircraft and radio transmitter with a battery.

Step 2

: Open

Openpilot

, and click

Input

at left side, then select

SBUS

for all channels under

Type, and set Chan1 –Chan5 under

Number

correspondingly (

Throttle

Roll

Pitch

, and

Yaw

are main channel, while

FlightMode

are aux channel to set the flight mode. To realize basic

flight needs, we only need to set these 5 channels. Then click

Save

Step 3

: Move the

Throttle

channel stick to check the channel value status on the

OpenPilot

If the

Pitch

changes when you move the

Throttle

channel stick, just exchange the channel

of Pitch and Throttle, then click

Save

. Now

Throttle

Chan3

, while

Pitch

Chan1

Step 4

: Move the

Elevator

channel stick.

SunFounder

Содержание Q250



















































Результаты поиска

Содержание Q250

Отзывы:

Похожие инструкции для Q250

Бренды по названию

Популярные бренды

SunFounder Q250, Руководство пользователя

Результаты поиска

Содержание Q250

Отзывы:

Похожие инструкции для Q250

Бренды по названию

Популярные бренды