Storm Century S-LSA Скачать руководство пользователя страница 47

Страница: 47 / 142

MAINTENANCE MANUAL

STORM Century S-LSA

STORM Century S-LSA

STORMAIRCRAFT

3.1.1 FLIGHT CONTROL INSPECTION

Open all inspection doors of the aircraft in order to carry out inspections and maintenance.
For flight control removal and installation, please refer to drawings in the aircraft structure chapter,
in the specific pages.
Check every

100 hours

if control stops are intact, inspect for wear, loosening or loss of

adjustment.
Check every

100 hours

if controls are easily operating, if they are smoothly running, free from

jamming, excessive friction or excessive elastic deformation.

FOLLOWING TOLERANCES ARE ACCEPTED FOR CONTROL SURFACES AND TRIM

downwards

upwards

Aileron

12°

2°

15°

2°

Rudder

25°

2° RH

25°

2° LH

Stabilator

20°

2°

32°

2°

Stabilator Trim

20°

2°

20°

2°

Movement and effect of aerodynamic controls in the cockpit

Aileron to right (clockwise) to lower the right wing
Stabilator backwards to pitch
Rudder

right pedal forward for heading right

Trim the hand movement on the switch shall be in the same

direction as the aircraft response (forward/nose down)

(backwards/nose up)

Содержание Century S-LSA















































































































































Результаты поиска

Содержание Century S-LSA

Отзывы:

Похожие инструкции для Century S-LSA

Бренды по названию

Популярные бренды

Storm Century S-LSA, Руководство по обслуживанию

Результаты поиска

Содержание Century S-LSA

Отзывы:

Похожие инструкции для Century S-LSA

Бренды по названию

Популярные бренды