Stihl MS 362 C-Q Скачать руководство пользователя

Страница: 43 / 52

MS 362 C-Q

English

Saw chains with humped drive link (2) –

upper part of the humped drive link (2)

(with service mark) is lowered at the

same time as the depth gauge of the

cutter.

WARNING

The rest of the humped drive link must

not be filed; otherwise, this could

increase the tendency of the chain saw

to kick back.

Rework the depth gauge so that it is

flush with the file gauge

Afterwards, dress the leading edge

of the depth gauge parallel to the

service mark (see arrow) – when

doing this, be careful not to further

lower the highest point of the depth

gauge

WARNING

Depth gauges that are too low increase

the kickback tendency of the chain saw.

Lay the file gauge on the saw chain

– the highest point of the depth

gauge must be flush with the file

gauge

After sharpening, clean the saw

chain thoroughly, removing any

filings or grinding dust – lubricate

the saw chain thoroughly

In the event of extended periods of

disuse, store saw chains in cleaned

and oiled condition

689BA051 KN

689BA044 KN

689BA052 KN

Sharpening tools (special accessories)
Chain pitch

Round file

File holder

File gauge

Taper square file Sharpening set

Inches

(mm)

mm (Inches) Part number

Part number

1/4P

(6.35)

3.2 (1/8)

5605 771 3206

5605 750 4300

0000 893 4005

0814 252 3356

5605 007 1000

1/4

(6.35)

4.0 (5/32)

5605 772 4006

5605 750 4327

1110 893 4000

0814 252 3356

5605 007 1027

3/8 P

(9.32)

4.0 (5/32)

5605 772 4006

5605 750 4327

1110 893 4000

0814 252 3356

5605 007 1027

0.325

(8.25)

4.8 (3/16)

5605 772 4806

5605 750 4328

1110 893 4000

0814 252 3356

5605 007 1028

3/8

(9.32)

5.2 (13/64) 5605 772 5206

5605 750 4329

1110 893 4000

0814 252 3356

5605 007 1029

0.404

(10.26) 5.5 (7/32)

5605 772 5506

5605 750 4330

1106 893 4000

0814 252 3356

5605 007 1030

consisting of file holder with round file, taper square file and file gauge

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды