Stihl MS 362 C-Q Скачать руководство пользователя

Страница: 33 / 52

MS 362 C-Q

English

If the groove is not at least this deep:

Replace guide bar

Otherwise the drive links will grind

against the base of the groove – the

bottoms of the cutters and the tie straps

will not lie against the bar.

The air filter system can be adapted to

suit different operating conditions by

installing a choice of filters. Changing

the filter is quick and simple.
The saw comes standard with either a

fleece filter or a fabric filter.

Fleece filter with felt prefilter

For normal, dry and very dusty work

areas.

Fabric filter

For severe winter conditions (e.g.

powder and drifting snow, frost).

If there is a noticeable loss of engine

power

Removing the shroud

Move the Master Control lever to the

stop position (0).

Push the hand guard forward – the

chain is locked.

Open the twist locks (1) by turning

them 1/4 turn counterclockwise with

the combination wrench.

Remove the shroud (2).

Removing the air filter

Clean away loose dirt from around

the filter.

NOTICE

To avoid damaging the filter, do not use

tools for removing and installing the air

filter.

Chain type Chain pitch Minimum

groove depth

Picco

1/4“ P

4.0 mm

Rapid

1/4“

4.0 mm

Picco

3/8“ P

5.0 mm

Rapid

3/8“; 0.325“ 6.0 mm

Rapid

0.404“

7.0 mm

Air Filter System

Cleaning the Air Filter

001BA199 KN

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды