Stihl MS 362 C-Q Скачать руководство пользователя

Страница: 24 / 52

MS 362 C-Q

English

For automatic and reliable lubrication of

the chain and guide bar – use only an

environmentally compatible quality

chain and bar lubricant. Rapidly

biodegradable STIHL Bioplus is

recommended.

NOTICE

Biological chain oil must be resistant to

aging (e.g. STIHL Bioplus) since it will

otherwise quickly turn to resin. This

results in hard deposits that are difficult

to remove, especially in the area of the

chain drive and chain. It may even cause

the oil pump to seize.
The service life of the chain and guide

bar depends on the quality of the

lubricant. It is therefore essential to use

only a specially formulated chain

lubricant.

WARNING

Do not use waste oil. Renewed contact

with waste oil can cause skin cancer.

Moreover, waste oil is environmentally

harmful.

NOTICE

Waste oil does not have the necessary

lubricating properties and is unsuitable

for chain lubrication.

Preparations

Thoroughly clean the oil filler cap

and the area around it to ensure that

no dirt falls into the tank.

Position the machine so that the

filler cap is facing up.

Open the filler cap.

Fill up with chain oil.

Refill the chain oil tank every time

you refuel.

Take care not to spill chain oil while

refilling and do not overfill the tank.
STIHL recommends you use the STIHL

filler nozzle for chain oil (special

accessory).

Close the filler cap.

There must still be a small amount of oil

in the oil tank when the fuel tank is

empty.

If the oil level in the tank does not go

down, the reason may be a fault in the oil

supply system: Check chain lubrication,

clean the oilways, contact your dealer

for assistance if necessary STIHL

recommends that you have servicing

and repair work carried out exclusively

by an authorized STIHL servicing

dealer.

Chain Lubricant

Filling Chain Oil Tank

001BA158 KN

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды