Stihl MS 362 C-Q Скачать руководство пользователя

Страница: 32 / 52

MS 362 C-Q

English

NOTICE

Always slacken off the chain again after

finishing work. The chain contracts as it

cools down. If it is not slackened off, it

can damage the crankshaft and

bearings.

Short-term storage
Wait for engine to cool down. Keep the

machine with a full tank of fuel in a dry

place, well away from sources of

ignition, until you need it again.

Long-term storage
See "Storing the machine"

Adjustable flow oil pump is a special

option.
Different quantities of oil are required for

different bar lengths, types of wood and

cutting techniques.

Use the adjusting screw (1) (on

underside of machine) to vary the oil

feed rate as required.
Ematic position (E),

medium oil flow rate –

turn the adjusting screw to "E"

(Ematic position).

To increase oil feed –

turn the adjusting screw clockwise.

Turn reduce oil feed –

turn the adjusting screw

counterclockwise.

NOTICE

The chain must always be wetted with a

film of lubricant.

Flip the bar – after each sharpening

and each time the chain is changed

– to avoid uneven wear, especially

at the sprocket nose and on the

bottom

Periodically clean the oil inlet

hole (1), oil outlet channel (2) and

bar groove (3)

Measure groove depth – using the

measuring tool on the file gauge

(special accessory) – in the area

with the greatest wear

Oil Quantity Control

001BA157 KN

Taking Care of the Guide Bar

143BA026 KN

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды