Stihl MS 362 C-Q Скачать руководство пользователя страница 25

Страница: 25 / 52

MS 362 C-Q

English

The saw chain must always throw off a

small amount of oil.

NOTICE

Never operate your saw without chain

lubrication. If the chain runs dry, the

whole cutting attachment will be

irretrievably damaged within a very short

time. Always check chain lubrication and

the oil level in the tank before starting

work.
Every new chain has to be broken in for

about 2 to 3 minutes.
After breaking in the chain, check chain

tension and adjust if necessary – see

"Checking Chain Tension".

The chain brake system has two

functions:

Standard STIHL chain brake

STIHL coasting brake

The coasting brake stops chain rotation

as soon as you release the saw's rear

handle.
To reduce the risk of damage or

personal injury during cutting, observe

the characteristics that make this saw

different from saws not equipped with a

coasting brake. Before operating the

chain saw for the first time, make sure

you are familiar with how the coasting

brake works.

Coasting brake is activated

When you let go of the rear handle.

Disengaging the coasting brake

Press down the throttle trigger

interlock lever. This releases the

clutch drum and allows the chain to

rotate.

Chain brake is activated

When the hand guard is pushed

towards the bar nose by the left

hand or by inertia in certain kickback

situations.

The chain is stopped and locked.

Checking Chain Lubrication

143BA024 KN

Chain Brake

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды