Stihl MS 362 C-Q Скачать руководство пользователя

Страница: 26 / 52

MS 362 C-Q

English

Disengaging the chain brake

Pull the hand guard back toward the

front handle.

NOTICE

Always disengage chain brake before

accelerating the engine (except when

checking its operation) and before

starting cutting work.
High revs with the chain brake engaged

(chain locked) will quickly damage the

powerhead and chain drive (clutch,

chain brake).

Chain brake is activated by inertia

If the kickback force of the saw is high

enough.
The hand guard is accelerated towards

the bar nose – even if your left hand is

not behind the hand guard, e.g. during

the felling cut.
The chain brake will operate only if the

front hand guard has not been modified

in any way.

Checking operation of the coasting

brake

Before starting work: Open the throttle

wide and then release the rear handle.

The chain must stop moving within less

than a second.

Checking operation of the chain brake

Before starting work: Run engine at idle

speed, engage the chain brake (push

hand guard towards bar nose) and open

the throttle wide for no more than

3 seconds – the chain must not rotate.

The hand guard must be free from dirt

and move freely.
In case of doubt about the above

functions, contact your servicing dealer

for assistance. STIHL recommends that

you have servicing and repair work

carried out exclusively by an authorized

STIHL servicing dealer.

Chain brake maintenance

The chain brake is subject to normal

wear. It is necessary to have it serviced

and maintained regularly by trained

personnel. STIHL recommends that you

have servicing and repair work carried

out exclusively by an authorized STIHL

servicing dealer. Maintain the following

servicing intervals:

Removing the shroud

Move the Master Control lever to the

stop position (0).

Push the hand guard forward – the

chain is locked.

Open the twist locks (1) by turning

them 1/4 turn counterclockwise with

the combination wrench.

Remove the shroud (2).

Full-time usage:

every 3

months

Part-time usage:

every 6

months

Occasional usage:

every 12

months

Winter Operation

001BA199 KN

Содержание MS 362 C-Q





















































Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды

Stihl MS 362 C-Q, Инструкция по эксплуатации

Результаты поиска

Содержание MS 362 C-Q

Отзывы:

Похожие инструкции для MS 362 C-Q

Бренды по названию

Популярные бренды