stertil ST1175 Скачать руководство пользователя страница 40

Страница: 40 / 108

Operation & Service Manual (VA)

ST1175

Safety guidelines:



When operating an individual column lift, the maximum permissible elevation

difference is 2".



When operating two column lifts (per-axle control), the maximum permissible

elevation difference between the front and rear axles is 6".



With a tandem axle at the rear of the vehicle, the maximum permissible

elevation difference between both rear axles is 2".

Center of gravity and weight distribution

If one of the columns is lowered too far, it can have the following consequences:



No load on that particular column.



No load on the column diagonally opposite.



Double load on the remaining columns.

Overloading of columns



Columns used for extremely rigid vehicles (aircraft towing vehicles, trains) will
quickly overload if a single column is lowered 3/8" to 2".

Содержание ST1175













































































































Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды

stertil ST1175, Руководство по обслуживанию

Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды