stertil ST1175 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 108

background image

Operation & Service Manual (VA)

44

ST1175

1 (ON)

This will activate the power supply to the column lift(s).

Follow the next described procedure to start the vehicle lift:

1. Turn the main switch to position [1] and press [SELECT] once.

This switches on the main and control circuit power, and the vehicle lift is ready for
use.



A control box on a slave column does not has a main switch.

6.4.3

Raising

To raise the column lifts, press the [UP] button. There is an arrow pointing up
beside this button.

6.4.4

Lowering

Activate the [UNLOCK] button simultaneously with the [DOWN] button to lower the
column lifts. There is an arrow pointing down next to the [DOWN] button.



If the foot protection has been enabled, the lowering action will be interrupted at
approx. 12" above the floor. The column will be lowered further, with an acoustic
signal, when the [UNLOCK] and the [DOWN] are pressed again simultaneously.
This option can be set by a technical service department recognized by Stertil.



If problem situations arise during raising or lowering, release the control buttons or

press the emergency stop.

WARNING

«
...
42
43
44
45
46
...
»

Содержание ST1175













































































































Отзывы:

Нет отзывов

Похожие инструкции для ST1175

Бренд: Clarke Страницы: 20

Бренд: Innova Страницы: 36

Gator Grip Drum EGG-1

Бренд: Wesco Страницы: 2

Бренд: Welding Industries Malaysia Страницы: 20

Бренд: HOLZMANN MASCHINEN Страницы: 29

Бренд: HURNER Страницы: 69

Compute Module IO Board Plus

Бренд: Waveshare Страницы: 17

Бренд: Telwin Страницы: 36

Бренд: Siku Страницы: 150

Бренд: M-system Страницы: 3

Бренд: SMAR Страницы: 47

Бренд: jbc Страницы: 20

Бренд: Marshall Amplification Страницы: 30

MAGSTOP MIB 10-C090

Бренд: Magnetic Autocontrol Страницы: 15

Бренд: Revo Страницы: 6

Бренд: ESAB Страницы: 28

Бренд: Miller Electric Страницы: 36

Бренд: Kamatec Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды