stertil ST1175 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 108

background image

Operation & Service Manual (VA)

7

ST1175

The lift operator or employer shall take all appropriate steps to follow the
recommended inspection procedures of the lift manufacturer but in no event shall
the lift operator fail to inspect or take notice of the following features on a daily
basis:

1. Accessibility and readability of the operating procedures, safety tips and generic

safety material.

2. Accessibility and readability of safety warning labels.

3. Readability of the rated load capacity of the lift.

4. Proper operation of the lift controls, restraints and locking devices.

5. Deformation or excessive wear of any of the lift structural components.

6. Deformation or excessive wear of other components such as hoses, electrical

wires.

7. Evidence of hydraulic leaks.

8. Unusual noises.

If any of the conditions described above are observed before, during or after
operation of the lift, the operator shall stop using the lift and report the condition to
the supervisor, employer or owner. If any of the conditions listed above are
observed, then the lift shall not be used until the cause of the problem has been
determined and the appropriate repairs made by qualified Stertil service
authorized personnel. In order to ensure that the lift is not used until the repairs
have been affected, the lift shall be locked out or tagged in accordance with
ANSI/Z244.1 2003 (R2008).



‘Trained lift service personnel’ refers to personnel of the Stertil service department
or another servici

ng agency recognized by Stertil, both also designated as ‘service

department’. The consequences of all repairs carried out on the vehicle lift by non-
trained lift service personnel, are entirely at the user's risk.

The owner or employer shall establish a periodic preventive maintenance
procedure in accordance with the recommendations listed in this manual.

Stertil USA shall not be responsible for any actions not specifically called out for in
this manual or in this notice.

Please note that there shall be no modifications or reconstruction made to the
Stertil mobile column lift without the express written permission of the
manufacturer.

Please make sure that caution labels are not frayed and are on the lift. Please call
the manufacturer if these caution labels have been removed or through age are no
longer on the lift.

Please read and understand the attached Statement of Warranty for the Stertil
mobile lift.

«
...
5
6
7
8
9
...
»

Содержание ST1175













































































































Отзывы:

Нет отзывов

Похожие инструкции для ST1175

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Бренд: TAC Страницы: 4

Бренд: Easylift Страницы: 127

Бренд: National Instruments Страницы: 23

Бренд: R. Beck Maschinenbau Страницы: 34

Бренд: NewArc Страницы: 12

Бренд: Nedap Страницы: 5

Бренд: WattMaster Страницы: 104

RazorCut 45 KUPJRRW45

Бренд: Unimig Страницы: 24

CONPROSYS CPS-MC341-DS1-111

Бренд: Contec Страницы: 71

Бренд: ATEN Страницы: 176

DIGITECH vision PULSE 3000

Бренд: CEA Страницы: 100

Бренд: Athena Страницы: 183

Бренд: Zennio Страницы: 2

Бренд: Sweiss Страницы: 89

Бренд: JLG Страницы: 48

Бренд: Micronix Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды