stertil ST1175 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 108

background image

Operation & Service Manual (VA)

61

ST1175

7.8.5

Program 64 - CE-stop

If this function is activated, the column stops lowering at a height of 10" or more.

To continue lowering, the buttons must be released and activated again. The
column lift will continue lowering with an intermittent audio signal. Within this range
an intermitting signal will always be present during lowering.



Blinking (default) = no CE-stop,



Steady = CE-stop.

7.8.6

Program 65 - Safe limits

This option is available so that the column can function outside the safe limits
(1 3/16" and 2 3/8"). This can be used to level the lift outside the safe limits.
Activating program 65 disables the safe limit monitoring.

This setting is active for 10 minutes and then the safe limits will be
automatically activated and the system has to be restarted. The setting will
not be saved in the EEPROM so that the safe limits will always be active
after starting and stopping.



Make program 65 active for each column in order to operate a column set outside

the safe limits.

7.8.7

Program 66 - Potentiometers OFF (check potentiometer
operation)

This option is available so that the value on the potentiometer input can be
replaced by a constant value. The column will function normally without the
elevation difference being corrected.

This setting is active for 10 minutes and then the safe limits will be
automatically activated and the system has to be restarted. The setting will
not be saved in the EEPROM so that the safe limits will always be active
after starting and stopping.



Make program 66 active for each column in order to operate a column set with

deactivated potentiometers.

«
...
59
60
61
62
63
...
»

Содержание ST1175













































































































Отзывы:

Нет отзывов

Похожие инструкции для ST1175

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 10

Бренд: Balboa Страницы: 23

Calc-An-Acre II

Бренд: micro-trak Страницы: 30

Бренд: TradeQuip Страницы: 7

Бренд: Orion Страницы: 23

MIG/MAG Welding Machine MIG/MAG 301 E

Бренд: Elektra Beckum Страницы: 36

Бренд: Yudian Страницы: 10

Бренд: ICP DAS USA Страницы: 156

Бренд: R-Tech Страницы: 19

Бренд: ENTRYPASS Страницы: 42

DRINKWORKS Home Bar Classic

Бренд: Keurig Страницы: 32

iAqualink IQ904-P

Бренд: Zodiac Страницы: 2

Бренд: WAGO Страницы: 92

Бренд: H&H Страницы: 23

Бренд: ICP DAS USA Страницы: 8

R7F4DC-DAC16D-H

Бренд: M-system Страницы: 8

ISaGRAF VP-2117

Бренд: ICP DAS USA Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды