stertil ST1175 Скачать руководство пользователя страница 74

Страница: 74 / 108

Operation & Service Manual (VA)

ST1175

8.4.2

The column lift will not lower

Cause

Solution

No mains power/control power.

Check the mains power/control power.
See section No mains power (on page
76) and section No control voltage (on
page 76).

The pawl does not retract from the
safety lock.

First allow the column lift to rise
approx. 1 3/8" and then allow it to
lower.

The electrically operated lowering
valve on the hydraulic unit will not
open.

There is no voltage on the lowering
valve or the lowering valve is faulty.
Have the technical service solve the
problem.

Dirty or damaged lowering valve.

Have the lowering valve cleaned or
have it replaced by the technical
service.

The maximum elevation difference
(more than 1 3/16") has been
exceeded.

Press [UP] until the elevation
difference has been leveled.

If lifting is not required, you can press
the [SELECT] button three times. Then
you can lower. The difference
of 1 3/16" persists.

If the fault occurs again, contact the
technical service.

The maximum height difference (more
than 2 3/8") has been exceeded.

Set the main switch to

OFF

and

Press the [SELECT] button once to
ensure the lifting system can be used
again.

If the fault occurs again, contact the
technical service.

The highest position is virtually the
same as the highest locking position.

Have the height set again by the
technical service.

Содержание ST1175













































































































Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды

stertil ST1175, Руководство по обслуживанию

Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды