stertil ST1175 Скачать руководство пользователя страница 55

Страница: 55 / 108

Operation & Service Manual (VA)

ST1175

5. When the oil level is too low, always perform the leak checks described later in this

chapter.

6. Inspection of all safety features.

7. Check for leakage from the cylinders. If oil is leaking from one of the cylinders, the

seals and the guide rings must be replaced.

8. Check for leakage from the hydraulic system. If the column lift sinks back down by

more than 1/4" per hour, then the system must be inspected for external (hoses,
couplings) and internal (valves) leakage. Defective parts must be replaced.

9. General inspection for damage. If cracks have appeared in structural components,

then the parts in question must be replaced. Immediately repair or replace all parts
which could cause hazardous situations.

10. Perform all lubrication tasks set out in section Lubrication instructions (on page

55).

For additional details, see chapter Troubleshooting (on page 67).

7.6

Regular preventive maintenance procedures

7.6.1

Lubrication instructions

The vehicle lifts must be serviced regularly in accordance with the lubrication
instructions.

Lubrication instructions

Maintenance
tasks

Description

Monthly

Per year
(technical
service)

Every 2
years
(technical
service)

Cylinder

Lubricate dry
piston-rod
(machine oil).

Check oil level in
tank

Top up (only with
column lifts fully
lowered).

Various pivot
points

Lubricate.

Hydraulic oil in the
tank

Replace; see
section Hydraulic
oil.

Suction filter

Clean or replace.

Safety lock

Check and clean
if required.

Содержание ST1175













































































































Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды

stertil ST1175, Руководство по обслуживанию

Результаты поиска

Содержание ST1175

Отзывы:

Похожие инструкции для ST1175

Бренды по названию

Популярные бренды