stertil ST1175 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 108

background image

Operation & Service Manual (VA)

19

ST1175

3.3.4

Personnel

Operating, maintenance and repair personnel, as well as anyone who is around
this vehicle lift should be aware of the possible dangers. This recommendation
applies regardless of other regulations that are issued by a higher authority or
included in a (safety) standard. The owner must ensure that employees are
qualified to perform the activities involved.



Employees must be aware of potential dangers.



Only trained and qualified operators may work on the vehicle lift. Inexperienced
operators can only work on the vehicle lift under supervision of an experienced
and trained person.



Persons under 16 years of age are prohibited from working on this vehicle lift in
any way whatsoever. Children under 14 years of age are not allowed in the
immediate vicinity of the installation.



When performing maintenance, always warn your colleagues at which location you
are working. Always turn the main switch to “O” and lock it with a padlock. If you
leave the vehicle lift unattended during maintenance, it is recommended to attach
a “DO NOT START” tag to the main switch and operator panel.



Working on or around the vehicle lift while under the influence of substances that

slow the ability to react is not permitted.

The following personal protection equipment is recommended for the engineer and
the user:



protective clothing,



gloves,



safety glasses,



ear protection,



safety shoes.



Do not wear loose-fitting clothing or jewelery.

WARNING

WARNING

«
...
17
18
19
20
21
...
»

Содержание ST1175













































































































Отзывы:

Нет отзывов

Похожие инструкции для ST1175

Бренд: Paton Страницы: 31

Бренд: Zepro Страницы: 52

Бренд: OMG Страницы: 16

Бренд: gala gar Страницы: 40

Бренд: Madas Страницы: 58

AeGIS 9100CR200

Бренд: PACH & COMPANY Страницы: 49

SE - 566 80 Habo

Бренд: Fagerhult Страницы: 6

Hy-Brid 3 Series

Бренд: Custom Equipment Страницы: 23

Бренд: Happ Страницы: 42

VIPER SYNERGIC MIG165

Бренд: Xcel-Arc Страницы: 58

Digital Car Puller 5000

Бренд: Telwin Страницы: 104

Бренд: BHM Medical Страницы: 29

Бренд: Revo Страницы: 6

Бренд: Mantracourt Страницы: 24

Бренд: Jefferson Страницы: 20

Devicenet R7F4DD-DA16B-C

Бренд: M-system Страницы: 7

MAJIC ATTIC LIFT

Бренд: Majic Stairs Страницы: 24

Бренд: Draper Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды