stertil ST1175 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 108

background image

Operation & Service Manual (VA)

20

ST1175

3.3.5

Safety instructions

Read all instructions. The vehicle lift is provided with safety and protection
features. Even so, caution is required when using the vehicle lift.

Work safely!

Stertil has made every effort to inform you as correctly and completely as possible
on any dangers associated with operation of the vehicle lift. You must ensure and
are responsible for compliance with these behavioral guidelines.

The buyer/user is obliged to familiarize operating, cleaning and maintenance
personnel with these instructions.

Upon their arrival, check deliveries for:



Any damage and/or missing parts due to transport. Make sure that the carrier

draws up a transport damage report on the spot.



Correctness and completeness; have all parts (additionally) and or accessories

ordered been supplied?

In the event of damage always contact Stertil or the supplier.



All worn or broken parts need to be replaced with genuine lift manufacturer

supplied parts.

Important safety instructions:
Read all instructions.
If an extension cord is necessary, use a cord with a
current rating equal to or more than the equipment.
Cords rated for less current than the equipment
may overheat. Take care to arrange the cord so
that it will not be tripped over or pulled.
Always unplug equipment from electrical outlet
when not in use. Never use the cord to pull the
plug from the outlet. Grasp plug and pull to
disconnect.
Let equipment cool completely before putting
away. Loop cord loosely around equipment when
storing.

WARNING

«
...
18
19
20
21
22
...
»

Содержание ST1175













































































































Отзывы:

Нет отзывов

Похожие инструкции для ST1175

Бренд: GANTERUD Страницы: 24

Бренд: heat-timer Страницы: 36

Metalmaster 200d Pro DC GTAW

Бренд: Tokentools Страницы: 33

Бренд: M-system Страницы: 10

Бренд: Carel Страницы: 2

Millermatic 212

Бренд: Miller Electric Страницы: 44

Бренд: SainSmart Страницы: 49

Бренд: Presto Lifts Страницы: 18

Бренд: Mobile Industrial Robots Страницы: 73

NOTIFIER CBC-CLASS 1

Бренд: Pittway Страницы: 20

Бренд: HURNER Страницы: 57

Бренд: BorMann Страницы: 33

Бренд: Hitbox Страницы: 18

Бренд: Kilsen Страницы: 16

Бренд: Solar 3C Страницы: 38

OERLIKON CITOTIG 1800 FORCE

Бренд: Lincoln Electric Страницы: 152

Бренд: iSMA CONTROLLI Страницы: 19

Бренд: AUTEC Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды