Optional R
emote Control
Place of Installation
Install the remote control panel in a dry place and in such away that you can
easily read the display and access the control buttons.
The installation location should be accessible easily.
The remote panel can be flush-mounted or top-mounted with or without frame:
Drill a hole for the wires into the back board. Slide the small left and right hand
covers (A) off the front panel which will expose the screws. Unscrew, remove the
frame (B) and drill the required holes into the back board. Connect all necessary
wires to the correct terminals at the back of the unit. Mount the unit using the
frame (B) and suitably long screws onto the back board.Reattach the covers (A)
onto the front panel.
Slide the small left and right hand covers (A) off the front panel which will
expose the screws. Unscrew and remove the frame (B). Use the inside of the
frame (B) as a template for the required cutout in the back board. Carefully cut
out the back board and connect all necessary wires to the correct terminals at the
back of the unit. Mount the unit using the four short screws supplied and reattach
the covers (A) onto the front panel.en.
Remove the small left and right hand covers (A) off the front panel and make a
cutout of 134mm x 90mm into the back board. Ideally, the back board should not
be thicker than 3mm; otherwise the front panel will stand back a little. Using the
actual Power Management Panel as a template, drill the required holes with
counterbores into the back board. Connect all necessary wires to the correct
terminals at the back of the unit. Push the unit from behind into the cutout and fix
it with the screws provided..
Avoid if possible laying the remote control cable next to any 230volts a/c cables
or next to high current d/c cables. This may cause interference and erroneous data
transmission. Remember, the remote control cable is purely a data transmission
working on very low voltages.
We strongly recomend not to shorten this cable. If you cut and reconnect the
cable this may void the warranty of your unit.
When all cables have been correctly laid and connected, reconnect the batteries
and the alternator.
The alternator-to-battery charger can be switched on and off manually by
pressing the on/off key ( assumming the alternato is working. Even when the
charger has been switched off, it will remain on standby mode. Also, the batteries
will still be charged, but without the boost on the domestic battery side.
After the unit has been switched on, the remote control will show the software
release of the charger and the remote control unit. In case you are experiencing a
problem with your alternator-to-battery charger, please take a note of these
numbers before you contact us.
When the engine is restarted, the alternator-to-battery charger will also restart,
even when the charger has been switched off manually before.
The alarm sound indicating any system faults can be muted using the alarm key.
The background light of the display panel can be switched on and off using the
light key.
Important: The panel must be installed in a dry place!
Basic Functions
1) Top-Mounting with Frame
2) Top-Mounting without Frame
3) Flush-Mounting
Installation of the Remote Control
1) Switching the charger on and off
2) Alarm Sound
3) Background Light
Connect the supplied remote control cable with the remote control unit. On the
back of the remote panel is a small opening with a socket behind. Mind the
correct orientation of the plug when you connect the cable. The small clip on top
of the plug must be directed upwards. Then, connect the remote control cable
with the corresponding connector on the alternator-to-battery charger. Again,
mind the correct orientation of the plug! (clip on top).
A
B
BOX INSTALLATION INSTRUCTIONS
SLIDE PARTS A TO EXPOSE SCREW HOLES
FOR FLUSH MOUNT, REMOVE PART B
FOR SURFACE MOUNT KEEP PART B
AFTER INSTALLATION REPLACE PARTS A
FOR MORE INFORMATION PUSH THE
BUTTON ON THE
REMOTE CONTROL. AND THE SCREENS WILL AUTOMATICALLY
SCROLL THROUGH,
FUNCTION
TO STOP THE AUTOMATIC SCROLLING AND LOCK ONTO ANY OF THE
BELOW SCREENS THEN SIMPLY PUSH THE FUNCTION BUTTON AGAIN
AND THE SCREEN WILL SAY SCROLL OFF AND LOCK ON THE SELECTED SCREEN
ALL VOLTAGE READINGS BELOW ARE JUST EXAMPLES
SCROLLING ON
AFTER YOU PUSH THE
FUNCTION BUTTON
SCREENS (START UP )
STERLING EUROPE
PRO MARINER USA
ABOUT 2 SECONDS
SEARCHING
****************
COMPANIES INVOLVED
IN THIS PRODUCT
SEARCHING FOR THE
COMS SIGNAL ,IF MORE
THAN A FEW SECONDS,
CHECK THE LINK CABLE
AND CONNECTORS
ABOUT 2 SECONDS
ALTERN > BATTERY
IN 12V - OUT 12V
PRODUCT INFORMATION
MODEL TYPE
ABOUT 2 SECONDS
BATTERY TYPE SET
FLOODED POS 6
SHOWING INFORMATION
ON THE BATTERY TYPE
SETTING, TO CHANGE
ADJUST BATTERY TYPE
POT
ABOUT 2 SECONDS
FAST CHARGE
14.8 VOLTS
SHOWING THE CHARGE
STATE & VOLTS IE
FAST/ADSORPTION/FLOAT
CHARGE.
DEFAULT SCREEN
ABOUT 2 SECONDS
STARTER OUTPUT
13.1 VOLTS
REFERS TO THE STARTER
BATTERY VOLTAGE
TAKEN AT OUR UNITS
TERMINAL
ABOUT 5 SECONDS
DOMESTIC BATTERY
NO DATA
REFERS TO THE DOMESTIC
BATTERY BANK VOLTAGE
IF THE REMOTE SENSE
WIRE IS USED ONLY. IF
NOT USED THEN NO DATA
ABOUT 5 SECONDS
POWER BOOST
20%
SHOWING BETWEEN
1-100% THIS IS THE
EFFECTIVE BOOST
1%= LITTLE WORK
100% = MAX WORK
ABOUT 5 SECONDS
UNIT INTERN TEMP
82 F 28 C
UNIT TEMP SHOWN
IN DEGREE C AND IN
DEGREE F THE UNIT WILL
SWITCH OFF AT 80 DEG C
ABOUT 5 SECONDS
ALTERNATOR TEMP
NO SENSE
ALTERNATOR TEMP
IF SENSOR FITTED, IF
SENSOR NOT FITTED THEN
NO SENSE.
ABOUT 5 SECONDS
BATTERY TEMP
NO SENSE
BATTERY TEMP
IF SENSOR FITTED, IF
SENSOR NOT FITTED THEN
NO SENSE.
ABOUT 5 SECONDS
FLOAT CHARGE
13.4 V
WHAT PART OF THE
CHARGE CYCLE THE
UNIT IS CURRENTLY ON
AND THE VOLTAGE. IE
FAST/ABSORBTION/FLOAT
ABOUT 5 SECONDS
DOMESTIC OUTPUT
14.7 VOLTS
DOMESTIC OUTPUT
VOLTAGE AT OUR STUD
ABOUT 5 SECONDS
ALTERNATOR INPUT
14.0 VOLTS
ALTERNATOR INPUT
VOLTAGE TAKEN AT THE
INPUT STUD AT
OUR UNIT
ABOUT 5 SECONDS
ADSORPTION TIME
154 MINS
WHEN THE CYCLE IS
ON ADSORPTION
MODE, THIS IS THE COUNT
DOWN TIMER UNTIL
IT GOES ONTO FLOAT
www.busse-yachtshop.de | [email protected]
