stayer 384B, Руководство по эксплуатации

Страница: 14 / 40

ENGLISH
14
14
To lock the pressed On/Off switch 7 , press the lock-on button 6 .
To switch off the machine, release the On/Off switch 7 or when it is
locked with the lock-on button 6 , briefly press the On/Off switch 7 and
then release it.
Adjusting the Speed
The speed of the switched on power tool can be variably adjusted,
depending on how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in a low rotational speed.
Further pressure on the switch results in an increase in speed.
Adjusting the Screw-in Depth
With the adjustment sleeve 3, the screw-in depth of the screw head into
the workpiece can be preset in 12 locking steps per full turn. Each step
corresponds with a 0.125 mm change of the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction results in a
greater screw-in depth; turning in anticlockwise direction reduces the
screwin depth.
The required setting is best determined by testing.
Working Advice
- Apply the power tool to the screw only when it is switched off.
Rotating tool inserts can slip off.
Guide the screw toward the screwdriving bit 1 . The screw is held in place
by the magnet pull of the universal bit holder 9 . Firmly push the tip of
the screw into the material to be screwed until the screwing-depth stop
4 faces against the
workpiece.
Switch the machine on. The screw is screwed into the material until the
adjusted screw-in depth is reached. The drive is disengaged and the
tool holder no longer rotates. Check the screw-in depth and readjust, if
required.
For unscrewing screws, set the rotational direction switch 8 to left rotation
and pull off the screwing-depth stop 4 toward the front without turning the
adjustment sleeve.
Working with the screwing-depth stop 4 is also possible when adapting
the screw-in depth.
Belt Clip
With the belt clip 5, the machine can be hung onto a belt. The user has
both hands free and the machine is always at hand.
Maintenance and Service
Maintenance and Cleaning
- Before any work on the machine itself, pull the mains plug.
- For safe and proper working, always keep the machine and ventilation
slots clean.
If the machine should fail despite the care taken in manufacturing and
testing procedures, repair should be carried out by an after-sales service
centre for Stayer power tools.
WARNING! Important instructions for connecting a new 3-pin plug to
the 2-wire cable. The wires in the cable are coloured according to the
following code:
Do not connect the blue or brown wire to the earth terminal of the plug.
Important: If for any reason the moulded plug is removed from the cable
of this power tool, it must be disposed of safely.
Transport
The contained lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements. The user can transport the batteries by road
without further requirements. When being transported by third parties
(e.g.: air transport or forwarding agency), special requirements on
packaging and labelling must be observed. For preparation of the item
being shipped, consulting an expert for hazardous material is required.
Dispatch batteries only when the housing is undamaged. Tape or mask
off open contacts and pack up the battery in such a manner that it cannot
move around in the packaging. Please also observe possibly more
detailed national regulations.
Disposal
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/UE for Waste
Electrical and Electronic Equipment and its implementation
into national right, power tools that are no longer usable
must be collected separately and disposed of in an
environmentally correct manner.
Battery packs/batteries:
Li-Ion:
Please observe the instructions in section “Transport”. Do not
dispose of battery packs/batteries into household waste, fire
or water. Battery packs/batteries should be collected,
recycled or disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be recycled according
the guideline 2006/66/CE.