Stanley SCD121, Руководство пользователя

Страница: 9 / 24

9
(
Original Instructions)
ENGLISH
Do not incinerate the battery pack.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and adjustment,
always remove the battery pack. Always switch
off the tool before inserting or removing the
battery pack.
WARNING: Use only STANLEY battery packs
and chargers.
Inserting and removing the battery pack from the tool
(Fig C)
WARNING: To reduce the risk of serious personal
injury, place the forward/reverse button in the
lock-off position or turn tool off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
NOTE: Make sure your battery pack (6) is fully charged.
To install the battery pack into the tool handle
1. Align the battery pack with the rails inside the handle.
2. Slide it firmly into place until you hear the lock snap into
place.
To remove the battery pack from the tool
1. Press the release button (5) and firmly pull the battery
pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
USE
Proper hand position (Fig A, H)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as
shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction. Proper hand position requires
one hand on the main handle (9).
Selecting the direction of rotation (Fig D)
For tightening, use forward (clockwise) rotation. For
loosening, use reverse (counterclockwise) rotation.
• To select forward rotation, push the forward/reverse
slider (2) to the left.
• To select reverse rotation, push the forward/reverse
slider to the right.
• To lock the tool, set the forward/reverse slider into the
centre position.
• When changing the position of the control button, be
sure the trigger is released.
Trigger switch (Fig A)
To turn the tool on, squeeze the trigger switch (1). To turn
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to select the best
speed for a particular application. The further you squeeze
the trigger, the faster the tool will operate. For maximum tool
life, use variable speed only for starting holes or fasteners
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
Torque adjustment collar (Fig. A,D)
The torque adjustment collar (3) is clearly marked with
numbers and a drill bit symbol.The collar should be rotated
until the desired setting is located at the top of the tool.
Locators are provided in the collar to eliminate the guess
work when selecting fastening torque.
The higher the number on the collar, the higher the torque
and the larger the fastener which can be driven. To lock the
clutch for drilling operations, move to the drill bit position.
NOTE: When using the drill/driver for drilling holes, be sure
that the torque adjusting collar is set so the figure of the drill
is aligned with the center line on the top ofthe tool. Failure
to do this will allow the clutch to slip while attempting to drill.
Gear shifter (Fig A, D)
The dual range feature of your driver/drill allows you to shift
gears for greater versatility.
To select the low speed, high torque setting, turn the tool
off and permit to stop. Slide the gear shifter (4) forward
(towards the chuck). To select the high speed, low torque
setting, turn the tool off and permit to stop. Slide the gear
shifter back (away from chuck).
NOTE: Do not change gears when the tool is running. If you
are having trouble changing gears, make sure that the dual
range gear shifter is either completely pushed forward or
completely pushed back.
LED work light
The LED work light (8) is located under the the torque
adjustment collar (3) and is activated automatically when
the trigger is depressed. The LED work light will illuminate
when the trigger is partially depressed, before the unit
begins running.
NOTE: The LED worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Keyless chuck (Fig E)
Your tool features a keyless chuck with one rotating sleeve
for one-handed operation of the chuck. To insert a drill bit or
other accessory, follow these steps.
1. Lock the trigger in the OFF position as previously
described.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
counterclockwise far enough to accept the desired
accessory.
3. Insert the accessory about 19 mm (3/4”) into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lockmechanism. This allows you to open and close the
chuck with one hand. To release the accessory, repeat
step 2 above.