Spokey ORYX 920865, Руководство пользователя

Страница: 9 / 60

8
LIST OF PARTS - DIAGRAM
– P. 50
No. Description Qty No. Description Qty
No. Description
Qty
1 counter 1
32 crank axle φ17*176L
1
63 sleeve φ10*φ15.8*6mm
1
2
resistance adjustment wire (from
the counter)
2
33 bolt M8*P1.25*12L*5T
3
64 sleeve φ10*φ15.8*9mm
1
3 pulse sensor wire (from the counter) 2
34 drive belt 410J6
1
65 magnets
1
4 bolt M5*12 4
35 right cover
1
66 resistance engine
1
5 left handlebar post cover 1
36 right pedal crank
1
67 bolt M8*P1.25*45L
1
6 right handlebar post cover 1
37 bolt M8*P1.0*20L
2
68 cover L
1
7 bolt M5*16 6
38 end cap
2
69 cover coupler
1
8 end cap 2
39 right pedal
1
70 C-clip Ф15.7*Ф19.4*1T
1
9 foam cover 2
40 bolt 3/16"*3/4"
6
71 wave washer Ф17.5*Ф25*0.3T
1
10 pulse sensor 2
41 flat washer Ф8*Ф16*1T
1
72 flat washer Ф17.5*Ф25*0.3T
1
11 handlebar 1
42 tensioner lever
1
73 rotation sensor grip
1
12 pulse sensor wire 2
43 tensioner roll
1
74 bolt ST3.5*1.4*12L
2
13 flat washer
Ф8*Ф14*2T
1
44 bearing 6000
2
75 bolt ST3.9*16L
8
14 spring washer
Ф8.5*Ф13.5*2.5T
15
45 nylon nut M8
4
76 front stabilizer right base
1
15 knob 1
46 main frame
1
77 front stabilizer
1
16 seat 1
47 sleeve φ10*φ14*3mm
1
78 bolt ST3.9*50L
7
17 end cap 1
48 bolt M8*P1.25*20L
1
79 left pedal crank
1
18 sleeve 2
49 spring ODφ12*φ1.8*53n
1
80 left pedal
1
19 knob 1
50 right rear stabilizer end cap
1
81 front stabilizer left base
1
20 end base 1
51 bolt ST3.9*1.4*20L
8
82 left pedal
1
21 bolt M6*12L 1
52 adjustable stabilizer foot M8
2
83
resistance adjustment wire (from the
handlebar post)
1
22 seat post 1
53 rear stabilizer
1
84 handlebar post
1
23 lower handlebar post cover 1
54 nut 3/8"-26*7T
2
85 curved washer
2
24
resistance adjustment wire (from
the main frame)
1
55 nut 3/8"-26*4.5T
3
86 sensor wire
1
25 flat washer
Ф8*Ф19*2T
11
56 bearing 6000
1
87 power cord
1
26 bolt 12
57 bearing 6003
2
88 resistance adjustment wire
1
27 knob 1
58 small pulley φ34*J8
1
89 wrench
1
28 sleeve in the seat column 1
59 single bearing φ35*17L
1
90 wrench
1
29 bearing 6203 2
60 left rear stabilizer end cap
1
91 Allen wrench
1
30 drive wheel 1
61 flywheel φ280*32W*6KG
1
92 power supply
1
31
sleeve φ17*φ22*10L
1
62 bearing 6300
1
93 spring
1
PREPARATIONS
1. Before assembly make sure there is enough space.
2. Use the recommended tools.
3. Before assembly check if there are all the parts in the box.
It is recommended that product should be assembled by at least two people
to avoid injuries.
Most of the assembly equipment listed here has been packed separately,
but some elements come preassembled in certain assembly parts. If it is
required, dissassemble them and assemble again.
Read the instructions of all assembly steps and familiarize with all the
devices installed.
ASSEMBLY INSTRUCTIONS ( Drawings
– p.
52-55)
Note: Follow the assembly instructions below:
STEP 1 Fix the front (77) and rear stabilizer (34) with spring washers
Ф8.5*Ф13.5*2.5T (14), flat washers Ф8*Ф19*2T (25), curved washers (85)
and bolts (26).
STEP 2 Place the lower cover (69) on the handlebar post (71), move it
upwards, so that it would not hinder the assembly.
Connect the resistance adjustment wires coming from the column (83) and
the main frame (24), next screw the handlebar post (71) with the main
frame (46). Use spring washers Ф8.5*Ф13.5*2.5T (14), flat washers
Ф8*Ф19*2T (25) and bolts (26).
STEP 3 Mount the handlebar (11). Before screwing it, remember to pull
through the pulse sensor wires through the handlebar post. Mount the
handlebar with the knob (15) and washers: the flat washer (13) and the
spring washer (14) as well as plastic covers (5). Screw the covers together
with the bolts (7).
STEP 4 Connect the pulse sensor wires (3 and 12) and resistance
adjustment wires (2, 83), next place the counter (1) on the top of the
handlebar post and fix it with bolts (4).
STEP 5 Place the seat (16) on the seat base, fix it by screwing in the knob
(19). Place the seat post (22) in a proper place in the main frame, secure it
with the knob (27).
STEP 6 Fix the pedals (80, 39) on the crank.
STEP 7 Screw the feet into the rear stabilizer. They will allow to level the
device easily.
NOTE: before you start the training, make sure that all the bolts and nuts
are securely tightened.
ASSEMBLY, SETUP AND MAINTENANCE