Spokey ORYX 920865, Руководство пользователя

Страница: 10 / 60

9
Remember to check if the blind of the front stabilizer is moveable, which
will make it easier to move the bicycle to another place.
The blinds of the back stabilizer are used to level the bicycle.
Levelling and Moving the device (pictures p. 56)
Before you start exercising, it is recommended to verify whether the bike is
positioned correctly. Please level the equipment by means of the stabilizer
knobs
To transport the device, raise it carefully on its front wheels and move to
another place, holding it on both sides.
Height adjustment of the bike saddle (drawing
– p.57)
Bike saddle height can be adjusted by removing the handwheel and setting
the saddle shank at the correct height.
The shank of the bike saddle has a few holes, i.e. a few possible ways to
get the right seat height.

To adjust the saddle height, loosen the bolt clamping the seat shank in
a bike frame.

Then select the appropriate seat height for a user by moving the saddle
shank up or down.

After selecting a given height, tighten the handwheel so that it is not
possible to change the position of the saddle shank.
Note: Do not remove the seat shank above the minimum or maximum signs
marked on the shaft of the bike saddle.
.
Resistance adjustment
The function of intensity regulation allows you to change pedal resistance.
High resistance requires a greater effort during pedalling while a low one
reduces the needed effort. Resistive force can be regulated by means of
the computer. To achieve a satisfying result, intensity should be adjusted
during workout, by means of knob UP (+) and DOWN (-).Available
resistance levels: from 1 to 16. The load system is independent of speed.
MAINTENANCE

Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.

Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.

The device should be kept in a dry place in order to protect it against
dampness and corrosion.

Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.

In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
should be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Power supply for the counter: 230V/50Hz or 60Hz Output: 8V DC 500 mA
COUNTER
First start-up
Before first start up please ensure that all cables are correctly connected.
Connect the power supply to the current. A U1 symbol will appear on the
display. Create your user profile (U1-U4) and go to
the training. You can also select the U1 profile, but
your results will not be saved.
Automatic start-up/shutdown (auto on/off)
The display will automatically start-up when you start moving the pedals or
press any button.
The display will automatically shut down when you stop the training for
longer than 4 minutes.
All settings and training data will be saved until next start-up.
In case when the display is not powering up, please disconnect the power
supply from the current and wait 15 seconds
Resetting
In order to zero all values, please press the TOTAL RESET button for three
seconds. The values will be removed and the console will reset.
Device error
If the displays does not show readings, please check if the wires are
connected correctly and whether the batteries need to be changed.
BUTTONS
SELECT When the trainer is stopped, press this button to go to the program
selection and to set the value flashing in the window . After selecting
appropriate program, press SELECT to confirm. In the settings mode, press
this button to confirm the entered value.
During the training, press SELECT to show speed, amount of rounds per
minute, or to choose automatic switch between the values.
START/STOP Press this button to start or stop the program operation.
Pressing and holding the START/STOP button for 2 seconds resets the
values shown by the counter.
COUNTER INSTRUCTIONS