manualshive.com logo in svg

Spectracom 8197, Инструкция по эксплуатации


Поделиться
Скачать
background image

Section 5:  Options and Accessories 

 

Page 5-2 

8197 Instruction Manual  

5.1 

OPTION 02 INTERNAL BATTERY BACKUP 

Option 02 provides the Model 8197 with an internal battery backup power source.  
The battery powers the Rubidium oscillator and GPS receiver whenever AC 
power fails or is turned off.  Battery backup shortens the recovery period to two 
hours when AC power returns by eliminating oscillator warm up and GPS 
reacquisition.  Without backup power, a 3-4 hour recovery period is required.  
The battery pack typically provides four hours of backup operation. 

NOTE:  

The battery backup powers only the oscillator and 

GPS receiver during AC power failures.  Outputs are not 
provided under backup operation. 

The battery is continuously float-charged whenever AC power is present.  
Maximum recharge period is 20 hours.  The battery is tested daily to verify 
battery operation.  At midnight “receiver time” the microprocessor enables the 
battery pack to power the oscillator and GPS receiver for approximately four 
minutes.  The battery test is transparent to unit operation.  If the battery falls 
below the minimum voltage set point, the test is discontinued and the Replace 
Battery alarm is asserted.  Refer to Section 6, Service Information, for battery 
replacement instructions. 
A battery disconnect switch is provided on the rear panel to prevent battery 
discharge when shipping or storing the Model 8197.  To disconnect the battery, 
first remove the unit from AC power and then depress the recessed switch 
labelled BATT DISC. 

NOTE:  

Failing to disable a battery prior to shipment or 

storage may result in reduced capacity and shortened 
battery life. 

5.1.1 Battery Lamps 

Units equipped with Option 02 include front panel indicators to communicate 
battery status. 

Ready Lamp

:  This green lamp is on when the battery is OK and fully charged.  

This lamp is off while the battery is tested. 

Charging Lamp

:  This yellow lamp is on when the battery is charging.  This lamp 

is off while the battery is tested. 

Replace Lamp

:  This red lamp turns on and a Minor Alarm asserted when the 

battery has remained in charge mode for two days or has failed the daily test.  
The battery must be replaced, refer to the service section of this manual. 

Содержание 8197


















































































































Отзывы:

Нет отзывов

Похожие инструкции для 8197

Magpowr PS90 Instruction Manuals preview
PS90
Бренд: Magpowr Страницы: 4
Earlex HG1500 Safety & Operating Instructions preview
HG1500
Бренд: Earlex Страницы: 4
Earlex HG1200 Safety And Operating Instructions preview
HG1200
Бренд: Earlex Страницы: 4
National Flooring Equipment PANTHER 5280 Service Manual preview
PANTHER 5280
Бренд: National Flooring Equipment Страницы: 28
Parkside PHLG 2000 SE - MANUEL 2 Bedienungs- Und Sicherheitshinweise preview
PHLG 2000 SE - MANUEL 2
Бренд: Parkside Страницы: 30
Parkside PES 200 B1 Operation And Safety Notes Translation Of Original Operation Manual preview
PES 200 B1
Бренд: Parkside Страницы: 56
Parkside PDSP 1000 B2 Operation Manuals preview
PDSP 1000 B2
Бренд: Parkside Страницы: 53
Parkside PAR 10.8 A1 Operation Manual preview
PAR 10.8 A1
Бренд: Parkside Страницы: 73
Parkside PBH 1500 A1 Translation Of Original Operation Manual preview
PBH 1500 A1
Бренд: Parkside Страницы: 20
Parkside PHLG 2000 SE - MANUEL 2 Manual preview
PHLG 2000 SE - MANUEL 2
Бренд: Parkside Страницы: 5
Parkside PFE 50 A1 Instruction Manual preview
PFE 50 A1
Бренд: Parkside Страницы: 55
Parkside PFE 50 A1 Original Instructions Manual preview
PFE 50 A1
Бренд: Parkside Страницы: 55
Parkside PAHKS 18V Manual preview
PAHKS 18V
Бренд: Parkside Страницы: 10
Parkside PGKGA 40-Li B2 Translation Of The Original Instructions preview
PGKGA 40-Li B2
Бренд: Parkside Страницы: 288
Parkside PDSS A1 Operation And Safety Notes Translation Of Original Operation Manual preview
PDSS A1
Бренд: Parkside Страницы: 35
Parkside PDSS A1 Operation And Safety Manual preview
PDSS A1
Бренд: Parkside Страницы: 35
Parkside PMFW 310 D2 Translation Of The Original Instructions preview
PMFW 310 D2
Бренд: Parkside Страницы: 50
Parkside PDMH 4500 A2 Operation Manual preview
PDMH 4500 A2
Бренд: Parkside Страницы: 45

Бренды по названию

Популярные бренды

Загрузить еще бренды