Spectracom 8197 Скачать руководство пользователя страница 3

Страница: 3 / 113

TABLE OF CONTENTS

SECTION 1

GENERAL INFORMATION

1.0 INTRODUCTION ....................................................................................................................1-1

1.1

FEATURES ............................................................................................................................1-2

1.2

WARRANTY INFORMATION AND PRODUCT SUPPORT..................................................1-2

1.3

MANUAL ERRATA AND SPECIAL DOCUMENTATION .....................................................1-3

1.4

UNPACKING..........................................................................................................................1-3

1.5 SPECIFICATIONS .................................................................................................................1-4

1.5.1

Receiver ....................................................................................................................1-4

1.5.2 Standard Frequency Outputs ....................................................................................1-4

1.5.3 Frequency Standard Stability ....................................................................................1-5

1.5.4

1 PPS Output.............................................................................................................1-5

1.5.5 1544 kHz Timing Outputs..........................................................................................1-6

1.5.6 2048 kHz Timing Outputs..........................................................................................1-6
1.5.7 Data Clock Timing Outputs .......................................................................................1-7

1.5.8 Data

Sync

Timing Outputs ........................................................................................1-7

1.5.9 Indicator Lamps .........................................................................................................1-8
1.5.10 Alarms .......................................................................................................................1-8

1.5.10.1 Alarms Classifications .................................................................................1-9
1.5.10.2 Tracking Alarm Classifications .................................................................1-10
1.5.10.3

Alarm Interface .........................................................................................1-10

1.5.11 Communication Ports ..............................................................................................1-11

1.5.11.1 RS-232 Com..............................................................................................1-11
1.5.11.2 RS-485 Com..............................................................................................1-11

1.5.12

Input Power .............................................................................................................1-12

1.5.13

Mechanical ..............................................................................................................1-12

1.5.14 Environmental..........................................................................................................1-13
1.5.15 Model 8225 GPS Antenna Specifications ...............................................................1-13
1.5.15.1 Electrical Specifications.............................................................................1-13
1.5.15.2 Mechanical Specifications .........................................................................1-13

1.5.16 Model 8226 Impulse Suppressor.............................................................................1-13

1.5.17 Model 8227 Inline Amplifier .....................................................................................1-14

SECTION 2

INSTALLATION

2.0 INTRODUCTION ....................................................................................................................2-1

2.1

MODEL 8225 GPS ANTENNA ..............................................................................................2-1

2.1.1

Antenna Installation ...................................................................................................2-1

2.2

ANTENNA CABLE..................................................................................................................2-2

2.2.1 Cable Lengths ...........................................................................................................2-3

2.3

MODEL 8226 IMPULSE SUPPRESSOR ..............................................................................2-3

2.4

MODEL 8227 GPS INLINE AMPLIFIER................................................................................2-4

2.5

MODEL 8197 PREPARATION FOR USE .............................................................................2-6

2.5.1

Antenna Connection..................................................................................................2-6

2.5.2

AC Power ..................................................................................................................2-6

2.5.3

DC Power ..................................................................................................................2-6

2.5.4

Chassis Ground.........................................................................................................2-7

2.6 INITIAL

OPERATION.............................................................................................................2-7

2.7

QUALIFYING THE INSTALLATION......................................................................................2-8

2.7.1

GPS

Signal Status ....................................................................................................2-8

2.7.2

Tracking Histogram .................................................................................................2-10

2.8

RECEPTION TROUBLESHOOTING...................................................................................2-11

2.8.1

Reception .........................................................................................................2-11

2.8.2

Low

GPS Quality .....................................................................................................2-12

2.9

FACTORY CONFIGURATION.............................................................................................2-12

Содержание 8197


















































































































Результаты поиска

Содержание 8197

Отзывы:

Spectracom 8197, Инструкция по эксплуатации, Страница: 3 / 113

Результаты поиска

Содержание 8197

Отзывы: