Spectra Watermakers Bimini 300 Скачать руководство пользователя страница 7

Страница: 7 / 78

Thank you

for your purchase of a Spectra Bimini 300 system. When properly installed and

maintained, it will provide years of trouble free service. Professional installation is strongly rec-

ommended. Like any piece of mechanical equipment, the system will require inspection and

service, so plan ahead for service access and install

“

service loops

”

in cabling. If a dealer is in-

stalling the system for you, review the location of the components to ensure the installation will

meet your approval upon completion.

Bimini Installation Quick Start

Important Details for Installer

1. The system must have a dedicated sea water inlet to guarantee a constant flow of water to the

system. The inlet should be as low in the boat as possible with a dedicated, forward

facing

scoop

type thru

hull fitting.

2. Both the Bimini 300 feed pump module and the Clark Pump/Membrane module must be in-

stalled in a well ventilated compartment where

temperatures

will not exceed 113°F (45°C).

Many engine compartments exceed this temperature when underway. Warranty will be void if

the installation does not meet this requirement.

3. Follow the wire gauge charts in the instructions! Using larger wire than specified is accepta-

ble.

4. If you are separating the Clark Pump/membrane assembly, please review the high pressure

tube assembly instructions. Improper assembly will cause failure!

5. Run, test, then sea trial the complete system before assuming it is operational. If the boat is in

fresh or dirty water, see Dry Testing the System. After testing, make sure the flush cycle oper-

ates properly. The water going overboard at the end of the flush should measure <1000 PPM

Total Dissolved Solids.

6. The Spectra Connect control must have DC power continuously to achieve the full benefits of

the fresh water flush system. The domestic fresh water pressure must be on and the fresh water

tank level maintained. Calculate about 7 gallons (27 liters) per flush.

7. The Spectra Connect control must be de

powered (DC power off) after the system is pickled

or winterized.

8. Spectra dealers are responsible for educating the vessel owners on the operation and mainte-

nance of the system. Please walk through the entire installation with our customer.

9. The equipment owner should fill out the warranty card or register online.

Содержание Bimini 300















































































Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды

Spectra Watermakers Bimini 300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды