Spectra Watermakers Bimini 300 Скачать руководство пользователя страница 26

Страница: 26 / 78

The optional Tank Level sensor allows even greater control of your ship

’

s fresh water systems. This

unique level monitoring system requires no holes to be drilled into your tank while measuring tank

volume with greater accuracy than a standard resistive float.

Turn off the ship

’

s domestic water system, close the fresh water supply valve at the water tank, then

bleed off the pressure by opening a tap in the galley or head sink.

Install a tee in the

water supply hose at the bottom of the tank, or at inlet to the domestic water

pump

. Connect open leg of the tee to the Tank Level Sensor. Note: The tank level sensor requires

1/4”

npt connection. We recommend installing a minimum

1/2”

tee, and using a reducing bushing

to connect the sensor.

Tank Level

Sensor

Fresh Water

Tank

Domestic

Water Pump

Connect:

Red to Red

White to White

Black to Black

If a 2nd Tank Level Sensor is going to be installed, it should be installed at the

base of the second tank.

If monitoring 2 water tanks, they must be isolated

from each other with a valve to read properly.

The wiring connections for the second Tank Level Sensor are located inside the

Spectra Connect control box.

See System Settings section of this manual for

instructions on enabling the second Tank Level Sensor.

See the Tank Level Calibration (pg. 28) in the Commissioning section of this

manual.

Optional Tank Level Sensor Installation

Route the 3 conductor cable back to the Spectra Connect control board at the feed pump mod-

ule. Extend the wires as necessary.

If you must extend the wires beyond

50’

contact the factory

to ensure proper operation.

Connect the Tank Level Sensor cables to the 3 conductors label Tank Level Sensors at the feed

pump module.

Polarity must be maintained!

Содержание Bimini 300















































































Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды

Spectra Watermakers Bimini 300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды