background image

Easy-Change Under-Sink Drinking Water Filter System 

Installation and Operating Instructions  

Model US-EZ

Specifications

Parts Included:

filter head with built-in bracket
filter cartridge
mounting screws
water supply adapter
lead-free faucet and fittings
1⁄4-inch plastic tubing
cartridge change reminder sticker

Precautions

  Do not use with water that is microbiologically unsafe or of 

unknown quality without adequate disinfection before or after the system. Systems 

certified for cyst reduction may be used on disinfected waters that may contain  

filterable cysts.

  This filter must be protected from freezing, which can cause cracking of 

the filter and water leakage.

  Because of the product’s limited service life and to prevent costly 

repairs or possible water damage, we strongly recommend that the head of the filter be 

replaced every ten years.  If the head of your filter has been in use for longer than this 

period, it should be replaced immediately. Date the top of any new head to indicate the 

next recommended replacement date.

  Turn off water supply to head without cartridge if it must be left 

unattended for an extended period of time.

NOTE: 

For cold water use only.
Make certain that installation complies with all state and local laws and regulations.
 The contaminants or other substances removed or reduced by the selected cartridge 

are not necessarily in your water. 
After prolonged periods of non-use (such as during a vacation) it is recommended 

that the system be flushed thoroughly. Let water run for 10 minutes before using.
The filter cartridges used with this system have a limited service life. Changes in 

taste, odor, and/or flow of the water being filtered indicate that the cartridge should 

be replaced.

The US-EZ-1 is tested and certified by NSF International to NSF/ANSI Standard 42 for 

the aesthetic reduction of Chlorine Taste and Odor and Nominal Particulate Class III.

Tools Required

phillips screwdriver

adjustable wrench

hand or electric drill 

(cordless recommended)

safety glasses

utility knife 

(for plastic tubing

)

Teflon

®

 tape

towel

center punch

pencil

1/4-inch & 9/16 or 5/8-inch drill bits

tape measure

file

Optional Materials

3" x 3" x 1/2" wood block

1/8-inch drill bit

CAUTION:

WARNING:

CAUTION:

CAUTION:

Range / Capacity

Level 1

Level 3

Level 4

Pressure Range:

30 – 100 psi (2.1 – 6.9 bar)

Temperature Range:

40–100 ° F (4.4 – 37.7 ° C)

Rated Service Flow:

0.5 gpm (1.9 Lpm)  

Filter Capacity:

3000 gallons (11,356 L)

500 gallons (1893 L)

Turbidity:

5 NTU max

The US-EZ-4 is tested and certified by NSF International to NSF/ANSI Standard 42 for the 

aesthetic reduction of Chlorine Taste and Odor, Chloramines and Nominal Particulate 

Class 1.  Standard 53 for the reduction of Cysts, Lead, Mercury, VOC, MTBE and Turbidity.

The US-EZ-3 is tested and certified by NSF International to NSF/ANSI Standard 42 for 

the aesthetic reduction of Chlorine Taste and Odor and Nominal Particulate Class 1.  

Standard 53 for the reduction of Cysts, Turbidity, Lead, Lindane and Atrazine.

 

146153   Rev C   12/06

Содержание US-EZ








Отзывы: