Spectra Watermakers Bimini 300 Скачать руководство пользователя страница 22

Страница: 22 / 78

Electrical continued

…

Wire Size Guide for the Bimini 300 12 Volt:

8 Gauge (10mm²) up to 15 feet (4.5M)

6 Gauge (16mm²) up to 20 feet (7.6M)

4 Gauge (25mm²) up to 35 feet (14M)

Wire Size Guide for the Bimini 300 24 Volt:

8 Gauge (10mm²) up to 30 feet (10.6M)

6 Gauge (16mm²) up to 45 feet (14M)

Note: If the specified circuit breaker sizes are una-

vailable, use the next higher rating but do not exceed the specification by more then 10%.

All wiring to be done to applicable ABYC, Marine UL, or CE standards.

Distances at left represent the total

ROUND TRIP wire length (DC pos-

itive length plus DC negative

length), NOT the length of the pair

of wires together. Size cables ac-

cordingly.

Mount the main power terminal block in a junction box or on a bulkhead adjacent to the feed

pump module. Make sure that this is a dry location well above bilge level and not subject to wa-

ter spray.

Be sure to install the terminal block cover.

Check the wire size chart for appropriate wire sizes. DC power feeds should be uninterruptible

to insure proper operation of the auto store feature. Avoid house breaker panels that could be

accidentally tripped.

Component Sizing:

•

Volt: Use a 25 Amp breaker and size the wiring for 25 Amperes.

•

Volt: Use a 15 Amp breaker and size the wire for 13 Amperes.

•

Provide circuit protection at the source! Undersized wiring will

Connect the yellow boost pump connector from the bottom of the feed pump housing to the

corresponding connector routed from the boost pump.

Содержание Bimini 300















































































Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды

Spectra Watermakers Bimini 300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Bimini 300

Отзывы:

Похожие инструкции для Bimini 300

Бренды по названию

Популярные бренды