background image

Spearhead TWIGA 

120

 

 

16

16

16

16

 

OPERATION

OPERATION

OPERATION

OPERATION    

Operation Safety 

Before commencing operation of the machine all operators must read this manual paying 
particular attention to the aspects relating to safe use of the machine. The operator is not 
only responsible for their own safety but also the safety of all other persons who enter into 
the close proximity of the working machine.  
 

Cable Controls 

Four levers individually control the operating 
functions of the machine the knobs of which are 
colour coded according to use. 
The function and operational direction of the 
levers are as follows where   indicates 
movement of the lever away from the operator 
and   indicates movement towards the operator: 
 
1. Red -   Reach Out and   Reach In. 
2. Yellow -   Lift Down and   Lift Up. 
3. Green -   Angle Up and   Angle Down. 
4. Black -   Cutterbar On and   Cutterbar Off. 
 

Proportional Controls 

On  proportional  models  all  operational  functions  are  controlled  by  a  single  joystick.  With 
the  power  switched  on  via  the  left hand  switch  on the  control box,  forward  and  rearward 
operation  of  the  joystick  controls  Lift  Down  and  Lift  Up  respectively  whilst  sideways 
operation controls Reach In and Reach Out – the particular sideways direction will depend 
on which side of the tractor the machine is working at the time. Angle function is controlled 
by  rotation  of  the  top  of  the  joystick.  The  centre  switch  on  the  control  box  switches  the 
cutterbar on and off. 
 
1. Reach In and Out 
 
2. Lift Up and Down 
 
3. Angle Up and Down 
 
4. Cutterbar On / Off 
 
 
 
 
 
 
 
Before commencing work it is advisable to find an unobstructed level site and operate the 
machine through its entire range of movements to familiarise yourself with the controls and 
the machines response to them. This is a wise precaution for all operators and a must for 
the inexperienced.  

 

 

Содержание TWIGA 120




































Отзывы: