background image

Spearhead TWIGA 

120

 

 

3

3

3

3

 

CAUTION: DO NOT OVER TORQUE HYDRAULIC FITTINGS AND HOSES 

 

TORQUE SETTINGS FOR HYDRAULIC FITTINGS 

HYDRAULIC HOSE ENDS 

 

PORT ADAPTORS WITH BONDED SEALS 

BSP 

Setting 

Metric 

 

BSP 

Setting 

Metric 

1/4” 

18 Nm 

19 mm 

 

1/4” 

34 Nm

 

19 mm 

3/8” 

31 Nm 

22 mm 

 

3/8” 

47 Nm

 

22 mm 

1/2” 

49 Nm 

27 mm 

 

1/2” 

102 Nm

 

27 mm 

5/8” 

60 Nm 

30 mm 

 

5/8” 

122 Nm

 

30 mm 

3/4” 

80 Nm 

32 mm 

 

3/4” 

149 Nm

 

32 mm 

1” 

125 Nm 

41 mm 

 

1” 

203 Nm

 

41 mm 

1.1/4” 

190 Nm 

50 mm 

 

1.1/4” 

305 Nm

 

50 mm 

1.1/2” 

250 Nm 

55 mm 

 

1.1/2” 

305 Nm

 

55 mm 

2” 

420 Nm 

70 mm 

 

2” 

400 Nm

 

70 mm 

 

WARRANTY POLICY

   

  

WARRANTY REGISTRATION 

 

All  machines  must  be  registered,  by  the  selling  dealer  with  Spearhead  Machinery  Ltd, 
before delivery to the end user.  On receipt of the goods it is the buyer’s responsibility to 
check  that  the  Verification  of  Warranty  Registration  in  the  Operator’s  Manual  has  been 
completed by the selling dealer. 
 

1. LIMITED WARRANTIES 

 

1.01. 

All machines supplied by Spearhead Machinery Limited are warranted to be free 

from defects in material and workmanship from the date of sale to the original purchaser 
for a period of 12 months, unless a different period is specified. 
 

1.02. 

All spare parts supplied by Spearhead Machinery Limited are warranted to be free 

from defects in material and workmanship from the date of sale to the original purchaser 
for a period of 6 months. 
 

1.03. 

The manufacturer will replace or repair for the purchaser any part or parts found, 

upon examination at its factory, to be defective under normal use and service due to 
defects in material or workmanship. Returned parts must be complete and unexamined. 
 

1.04. 

This warranty does not apply to any part of the goods, which has been subjected to 

improper or abnormal use, negligence, alteration, modification, fitment of non-genuine 
parts, accident damage, or damage resulting from contact with overhead power lines, 
damage caused by foreign objects (e.g. stones, iron, material other than vegetation), 
failure due to lack of maintenance, use of incorrect oil or lubricants, contamination of the 
oil, or which has served its normal life. This warranty does not apply to any expendable 
items such as blades, flails, bushes, belts, flap kits, skids, shields, guards, wear pads or 
pneumatic tyres. 
 

Содержание TWIGA 120




































Отзывы: