background image

Spearhead

 

Multi-Cut 

420

 

 

6

 

 

  Disengage the machine, stop the engine and remove the key before leaving 

the tractor cab for any reason 

  Clean up any debris left at the work site. 

  Ensure that when you remove the machine from the tractor it is secured in a 

safe position using the stands provided, on level concrete base. 

 

NEVER: 

  Never operate the machine with other people present, as it is possible for 

debris, including stones, to be discharged from the front and rear. 

  Never operate the machine until you have read and understood this 

handbook and are familiar with the controls. 

  Never use a machine that is poorly maintained or has guards that are 

damaged or missing 

  Never allow an inexperienced person to operate the machine without 

supervision. 

  Never use or fit a machine onto a tractor if it doesn’t meet the 

manufacturer’s specification. 

  Never use a machine if the hydraulic system shows signs of damage. 

  Never attempt to detect a hydraulic leak with your hand, use a piece of 

card. 

  Never allow children to play on or around the machine at any time. 

  Never attempt any maintenance or adjustment without first disengaging 

the PTO, lowering the wings to the ground, stopping the tractor engine 
and applying the tractor parking brake. 

  Never leave the cab without removing the ignition key. 

  Never operate the tractor or any controls from any position other than 

from the driving seat. 

  Never stop the engine with the PTO engaged. 

  Never operate with blades missing. 

  Never operate PTO above recommended speed, 1000 r.p.m. 

  Never operate with wire around the rotor.  Stop immediately. 

  Never use the wing raised which may throw debris towards the cab. 

  Never attempt to use the machine for any purpose other than that it was 

designed for. 

  Never transport with the PTO engaged. 

  Never enter the working area of the machine (risk of injury!). 

  Never engage the P.T.O with wings folded. 

Содержание Multi-Cut 420























Отзывы: