background image

Spearhead

 

Multi-Cut 

420

 

 

15

 

 

Service & Maintenance – Every 8 hours 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

  Dismantle and clean the main P.T.O shafts sliding surfaces and re-grease; 

failure to do this will result in serious damage to the gearboxes. 

  Grease all universal joints, if under-greased this joint will soon fail. 

  Grease the wing drive shaft tubes. 

  Lubricate the retaining collar on all the drive shaft guards (Fig. 9). 

  Grease PTO inner tube and push pins (Fig. 9). 

 

Check all bolts are tightened to the correct Torque (Fig.10).

 

 

 

Torque Settings 

 
 
 
The Torque figures given below are recommended maximum settings only.

 

 

 

Size: 

Tensile strength: 

Description: 

Torque setting: 

Nm. 

M16 

8.8 

Rotor gearbox bolts 

280 

¾ UNC 

8.8 

Splitter gearbox 

280 

M24 8.8 

Blade 

bolts  950 

  Wheel 

nuts 

270 

M14   PTO 

clamp 

bolt 

150 

 

                                                                                 

 

  For maximum life and performance, the UJ must be greased regularly. Lubricate the driveline 

up to 6 pumps of grease may be required. 

  The metal drive tubes must be greased to telescope properly. 

  Shielding is subject to damage from abuse and weathering.  Replace all damaged 

components and all shielding removed during maintenance. 

 

Do not use PTO adapters drivelines. Replace special clamp bolts only with genuine OEM 
parts, periodically check tightness of nuts.

 

Primary Input Shaft

 

Fig 10 

Fig 9 

Содержание Multi-Cut 420























Отзывы: