background image

Spearhead

 

Multi-Cut 

420

 

 

5

 

 

Recommendations 

 

Beware of the following Potential Dangers associated with the use of 
this machine: 

  Becoming trapped when hitching or unhitching 

  Machine overbalancing when wing is raised. 

  Getting caught on rotating power take off (PTO) 

  Being hit or caught by any moving part, e.g. Blades, drive shaft and wings. 

  Being hit by flying debris or machine parts due to machine damage 

  Machine overbalancing when not in use 

  Injection of high pressure oil from damaged couplings or hydraulic hoses 

 

Accidents due to collision with other machines, or debris left on road

 

 

Beware of free-swinging blades over centering and falling when wings are 
folding.

 

 

ALWAYS: 

  Ensure the operator has read this handbook and has been trained to use the 

machine. 

  Ensure all safety guards are in place and all tractor windows closed.

 

  Impact resistant shielding to the tractor is recommended

 

  Before leaving the tractor cab always ensure that the wings are firmly on the 

ground, no weight is on the machine’s hydraulics and the rotor has stopped 
spinning. 

  Check that all guards are properly fitted and there are no damaged or loose 

parts. Particular attention should be given to the blades to ensure they are not 
damaged, cracked or missing. 

  Inspect work area for wire, steel posts, large stones and other dangerous 

materials and remove before starting work. 

  Ensure that all warning labels are always visible and that they are not 

damaged, defaced or missing. 

  Fit locking bars to height and to wings before transport and before unhitching 

when applicable. 

  Wear ear defenders if operating without a quiet cab or with the cab windows 

open 

  Ensure tractor guards are fitted correctly and are undamaged 

  Work at a safe speed, taking into account terrain, passing vehicles and 

obstacles 

  Ensure that the tractor meets the minimum weight recommendations of the 

machine manufacturer and that ballast is used if necessary 

  Check that machine fittings and couplings are in good condition 

  Follow the manufacturer’s instructions for attachment and removal of machine 

from the tractor 

  Ensure blades are of the type recommended by the manufacturer, are 

securely fitted and are undamaged 

  Ensure hydraulic pipes are correctly routed to avoid damage from chafing, 

stretching, pinching or kinking. 

  Check condition of tyres and tightness of wheel nuts. 

  Ensure all blades have stopped spinning before folding wings into transport 

position.

 

Содержание Multi-Cut 420























Отзывы: