background image

Spearhead

 

Multi-Cut 

420

 

 

9

 

 

Setting Up Your Machine 

 

 

Height 

To alter the height of cut; raise the machine so the wheels are clear of the ground, 
remove pin 

(Fig. 3) adjust the wheel arm, replace pin 

(Fig 3) and gently lower the 

machine until the wheel contacts the ground. Fine adjustment can be made by 
moving the spacers on the wheel fork above or below the wheel arm, spacer 

b

 (Fig 

3). Now adjust the height of the tractor link arms so the front of the mower is 25mm 
(1”) higher at the front 

c

The top link must be adjusted to ensure the wire ropes are slack, so the machine can 
follow undulating ground fore and aft, but still allow the machine to lift when the 
tractor link arms are fully raised. 

 

 

Wings 

Unfolding the wings if the machine is in the transport position, first pressurise 
hydraulic rams before releasing locking bar (Fig 4), lower both wings by releasing 
hydraulic pressure, leaving tractor spool in float position (Fig, 5). 
 

 

 

 

 

 
 

Levelling the wing cutting height LH & RH 

With the wings lowered, adjustable skids alter cutting height, these should be set to 
maintain minimum cutting height 12mm (1/2”) above the centre blades. When fitted 
with optional wheels to the wings, the skids should be raised above the ground and 
the cutting height controlled by the height of these wheels.  
Note 
To achieve a level cut with the wing wheels, they need to set lower than the centre 
wheels. 

Height adjusting 
spacer 

Cutting height 
adjustment

 a 

Ensure front of 

machine is 25mm 
(1”) higher than rear 

Fig 3 

Fig 4 

Adjustable side 
skids 

Transport locking 
bar

 

Содержание Multi-Cut 420























Отзывы: