South Bend Tools SB1007, Руководство пользователя

Страница: 81 / 84

South Bend Tools
For Machines Mfd. Since 12/21 Model SB1007
-79-
P A R T S
Machine Labels – Front
To reduce the risk of serious personal injury while
using this machine:
1. Read and understand owner’s manual before
starting.
2. Always wear approved safety glasses AND a
face shield.
3. Only plug power cord into a grounded outlet.
4. Tie back long hair, roll up sleeves. DO NOT
wear loose clothing, gloves, or jewelry.
5. Disconnect power before setting up, adjusting,
or servicing.
6. Rotate workpiece by hand to ensure clearance
before starting.
7. Test each new workpiece setup for safe rotation;
start with slowest speed and stand to side of
lathe until safe rotation verified.
8. Keep all guards and covers in place during
operation.
9. Never leave chuck key in chuck.
10. Never leave lathe running unattended.
11. DO NOT reverse spindle rotation while spindle
is moving.
12. Properly support long workpieces with
appropriate rest.
13. DO NOT expose to rain or use in wet locations.
14. Prevent unauthorized use by children or
untrained users.
WARNING! !
Specifications
MODEL SB1007
Made in Taiwan to South Bend Specifications
Date
Serial No.
Req. Power Supply: 220V, 1-Ph, 60 Hz
Full-Load Current Rating: 5.5A
Motor: 2 HP, 220V, 3-Ph
Swing Over Bed: 10-3/4"
Distance Between Centers: 30"
Swing Over Cross Slide: 6-5/8"
Cross Slide Travel: 4-5/8"
Spindle Nose: D1-4
Spindle Bore: 1.358" (34.5mm)
Spindle Taper: MT#5
Tailstock Taper: MT#3
Tailstock Quill Travel: 3-1/8"
Weight: 494 lbs.
HARDENED AND GROUND
South Bend ®
Three V-Way Bed
www.southbendlathe.com
Made in Taiwan
South Bend
®
www.southbendlathe.com
Made in Taiwan
South Bend
®
OFF ON
1 2
Power
Light
SB1007
HEAVY 10
™
LATHE
South Bend Lathe
®
NON
NUMBERED
POSITION
ANY
POSITION
8, 16, 24, 32, 40, 48, 56,
64, 72, 80, 96, 112, 128
12, 20, 28, 36, 44, 52,
76
6, 10, 14, 18, 22, 26,
38, 54
5, 7, 9, 11, 13, 19, 27
4 1 / 2, 9 1 / 2
NUMBERED
POSITION
NUMBERED
POSITION
1, 3, 5, 7
POSITION
1,5 OR 3,7
5
4
3 2
1
8
7 6
1 IN
REV
FWD
OFF JOG
701
702
703
704
705
706 707 708 709 710
711
712 713
714
715
WARNING!
!
ENTANGLEMENT
HAZARD
Remove or secure
loose clothing, hair
or jewelry to reduce
the risk of serious
injury or death.
Using excessive
spindle speeds can
result in serious
impact injuries or
death! Always use
slow spindle speeds
with large or
non-concentric
workpieces. Never
exceed chuck RPM
rating.
WARNING! !
WARNING!
!
INJURY HAZARD
Always remove chuck
key from chuck after
making adjustments to
reduce the risk of
personal injury.
EYE INJURY HAZARD
Always wear ANSI-
approved safety
glasses or a face
shield when using
this equipment.
WARNING! !
INJURY HAZARD
Do not use machine if
you have not read the
manual. Visit
southbendlathe.com
or call 360-734-1540
to get a manual.
WARNING! !
7 16
A A
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
.0018
.0020
.0024
.0029
.0032
.0040
.0048
.0058
.0064
64
56
48
40
36 32
28
24
20
18 .0036 .0072
.0080
.0096
.0116
.0128
0.5
0.6
0.75
1.0
1.5
2.0
16
14
12
10
9
3 5 1 4 2 A C B
C B
127
90 90
120
30
127
30
90
127
30
INCHES
INCHES
MM
TPI
B C
• Do not expose to rain or use in
damp locations.
• AVERTISSEMENT!: Ne pas exposer
à la pluie et ne pas utiliser dans
les emplacements humides.
• Wear eye protection.
• Porter des lunettes de protection.
• Do not wear gloves, necktie, or
loose clothing.
• Ne pas porter de gants, de cravate,
ou de vêtements amples.
• Tighten all locks before operating.
• Serrer tous les serrure avant
exploitation.
WARNING! !
717
The safety labels provided with your machine are used to make the operator aware of the
machine hazards and ways to prevent injury. The owner of this machine MUST maintain the
original location and readability of these safety labels. If any label is removed or becomes
unreadable, REPLACE that label before using the machine again. Contact South Bend Tools at
(360) 734-1540 or www.southbendtools.com to order new labels.
RREEFF PPA ARRTT ## DDEES SCCRRIIPPTTIIOONN RREEFF PPA ARRTT ## DDEES SCCRRIIPPTTIIOONN
701 PSB1007701 SOUTH BEND ROUND NAMEPLATE 710 PSB1007710 CHUCK KEY WARNING LABEL
702 PSB1007702 MASTER POWER LABEL 711 PSB1007711 FEED RATE LABEL
703 PSB1007703 SPINDLE SPEED CHART 712 PSB1007712 READ MANUAL LABEL
704 PSB1007704 SOUTH BEND RECTANGULAR LOGO 713 PSB1007713 EYE INJURY HAZARD LABEL
705 PSB1007705 SOUTH BEND GREY TOUCH-UP PAINT 714 PSB1007714 THREAD DIAL LABEL
706 PSB1007706 V-WAY DESCRIPTION LABEL 715 PSB1007715 MACHINE ID LABEL
707 PSB1007707 ENTANGLEMENT HAZARD LABEL 716 PSB1007716 WARNING LABEL
708 PSB1007708 SPINDLE SPEED WARNING LABEL 717 PSB1007717 WARNING LABEL FRENCH
709 PSB1007709 CONTROL PANEL LABEL