South Bend Tools SB1007 Скачать руководство пользователя страница 53

Страница: 53 / 84

South Bend Tools

For Machines Mfd. Since 12/21

Model SB1007

-51-

M A I N T E N A N C E

MAINTENANCE

Maintenance Schedule

For optimum performance from your lathe, follow

this maintenance schedule and refer to any

specific instructions given in this section. For

your convenience, an easy-to-use maintenance

chart has been included on the following page.

Ongoing

The condition of lathe components should be

carefully observed at all times to minimize the

risk of injury or machine damage. If any of the

conditions below are observed, stop the lathe

immediately, disconnect power, and correct the

condition before resuming operations:

• Loose mounting bolts or fasteners.

• Worn, frayed, cracked, or damaged wires.

• STOP button not working correctly or not

requiring you to reset it before starting the

lathe again.

• Oil level not visible in the sight glasses.

• Components damaged or malfunctioning.

Daily, Before Operations

• Check/add headstock oil (Page 52).

• Check/add gearbox oil (Page 53).

• Lubricate the bedways (Page 54).

• Clean/lubricate leadscrew (Page 54).

• Add oil to ball oilers (Page 54).

• Disengage feed selection lever on apron (to

prevent crashes upon startup).

• Ensure carriage lock screw is loose.

Always disconnect

lathe from power before

performing maintenance or

serious personal injury may

result.

Daily, After Operations

• Press STOP button and turn master power

switch to OFF.

• Vacuum/clean all chips and swarf from bed

and ways.

• Wipe down all unpainted or machined

surfaces with an oiled rag.

Monthly

• Check

timing belt for tension or wear.

Annually

• Change headstock oil (Page 52).

• Change gearbox oil (Page 53).

• Lubricate end gears (Page 55).

• Check/level bedway (Page 22).

Cleaning & Protecting

Regular cleaning is one of the most important

steps in taking care of this lathe. We recommend

planning a cleaning routine into the workflow

schedule, so that adequate time is set aside to do

the job well.

Typically, the easiest way to clean swarf from the

bed ways is to use a wet/dry shop vacuum. Small

chips left over after vacuuming can be wiped up

with a lightly oiled rag. Avoid using compressed

air to blow off chips, as it may drive them more

deeply into moving surfaces and could cause

sharp chips to fly into your face or hands.

All unpainted and machined surfaces should be

wiped down daily to keep them rust free and in

top condition. This includes any surface that is

vulnerable to rust if left unprotected. Typically, a

thin film of quality way oil is all that is necessary

for protection.

Содержание SB1007





















































































Результаты поиска

Содержание SB1007

Отзывы:

Похожие инструкции для SB1007

Бренды по названию

Популярные бренды

South Bend Tools SB1007, Руководство пользователя

Результаты поиска

Содержание SB1007

Отзывы:

Похожие инструкции для SB1007

Бренды по названию

Популярные бренды