manualshive.com logo in svg

South Bend Tools SB1007, Руководство пользователя


Поделиться
Скачать
background image

South Bend Tools

For Machines Mfd. Since 12/21

Model SB1007

-17-

P R E P A R A T I O N

Inventory

Unpacking

This item was carefully packaged to prevent 

damage during transport. If you discover any 

damage, please immediately call Customer 

Service at (360) 734-1540 for advice. You may 

need to file a freight claim, so save the containers 

and all packing materials for possible inspection 

by the carrier or its agent.

Some inventory components may be shipped 

inside of the lathe electrical box. These items 

MUST be removed before connecting the lathe 

to the power source.

If you cannot find an item on this list, carefully 

check around/inside the machine and 

packaging materials. Often, these items get 

lost in packing materials while unpacking or 

they are pre-installed at the factory.

Figure 

Figure 9. Main inventory.

. Main inventory.

A

A

C

C

B

B

Main Inventory 1: (Figure 9) 

Qty

A.

  3-Jaw Chuck 6" w/Back Plate .......................1

B.

  Outside Jaw Set (3-Pc) ...................................1

C.

  3-Jaw Chuck Key ...........................................1

Toolbox Inventory: (Figure 10) 

Qty

D.

 Toolbox ............................................................1

E.

  Tapered Spindle Sleeve MT#5-#3 .................1

F.

  Oil Can ............................................................1

G. 

Open-End Wrench 13mm ..............................1

H.

 Open-End 

Wrench Set 6-Pc. (8-23mm) .........1

I.

  Flat Head Screwdriver #2 .............................1

J.

  Phillips Head Screwdriver #2 ........................1

K. 

Hex Wrench Set 9-Pc. (1.5-10mm) ................1

L.

  Handwheel Handles .......................................2

M.

  Electrical Box Key ..........................................1

N.

  Master Power Key ..........................................1

O.

  Gear Drive Shaft ............................................1

P.

  Change Gear Set ............................................1

 

—Change Gear (95T) .....................................1

 

—Change Gear (80T) .....................................1

 

—Change Gear (70T) .....................................1

 

—Change Gear (65T) .....................................1

 

—Change Gear (60T) .....................................1

 

—Change Gear (55T) .....................................1

 

—Change Gear (50T) .....................................1

 

—Change Gear (45T) .....................................1

 

—Change Gear (40T) .....................................1

 

—Change Gear (35T) .....................................1

Q. 

Headstock

 

Top Cover (Not Shown) ...............1

Figure 

Figure 10. Toolbox inventory.

. Toolbox inventory.

II

H

H

E

E

F

F

LL

N

N

P

P

D

D

G

G

JJ

K

K

O

O

M

M

Содержание SB1007





















































































Отзывы:

Нет отзывов

Похожие инструкции для SB1007

Nederman 42221601 Instruction Manual preview
42221601
Бренд: Nederman Страницы: 28
Nederman filtermax c25 Instruction Manual preview
filtermax c25
Бренд: Nederman Страницы: 30
Jet JDC-500B Operating Instructions And Parts Manual preview
JDC-500B
Бренд: Jet Страницы: 12
Jet 500 Specifications preview
500
Бренд: Jet Страницы: 1
Craftex CX405 User Manual preview
CX405
Бренд: Craftex Страницы: 15
Craftex CX401 User Manual preview
CX401
Бренд: Craftex Страницы: 16
Craftex CT186 User Manual preview
CT186
Бренд: Craftex Страницы: 17
ACT LASERPACK Installation And Operation Manual preview
LASERPACK
Бренд: ACT Страницы: 18
Blastrac BDC-44 Operating Instructions Manual preview
BDC-44
Бренд: Blastrac Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды