SoundCraft Vi5000 Скачать руководство пользователя страница 2

Страница: 2 / 225

Vi5000/7000 User Manual

IMPORTANT INFORMATION

IMPORTANT INFORMATION

IMPORTANT

Please read this manual carefully before using your mixer for the

first time.

This equipment complies with the EMC directive 2004/108/EC

and LVD 2006/95/EC

This product is approved to safety standards

IEC 60065:2001 (Seventh Edition) +A2:2010

EN60065:2002 +A1:2006 +A2:2010 +A11:2008 +A12:2011

UL60065 2012 7th Edition

CAN/CSA-E60065-03 + A2: 2012

And EMC standards

EN55103-1: 2009

EN55103-2: 2009

Warning: Any modification or changes made to this device, unless explicitly approved by

Harman, will invalidate the authorisation of this device. Operation of an unauthorised

device is prohibited under Section 302 of the Communications act of 1934, as amended,

and Subpart 1 of Part 2 of Chapter 47 of the Code of Federal Regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna

* Increase the separation between the equipment and the receiver

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help

Parts of the design of this product may be protected by worldwide patents.

Part No. 5061286

Rev 1.0

E&OE September 2015

Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change

without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any

loss or damage whatsoever arising from the use of information or any error contained in this manual. No part of this

manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,

electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express

written permission of Soundcraft.

Harman International Industries Limited

Cranborne House, Cranborne Road, Potters Bar, Hertfordshire, EN6 3JN, UK

Tel: +44 (0)1707 665000

Fax: +44 (0)1707 660742

http://www.soundcraft.com

Содержание Vi5000


































































































































































































































Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды

SoundCraft Vi5000, Руководство пользователя

Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды