SoundCraft Vi5000 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 225

background image

Vi5000/7000 User Manual

®

MENU > SETTINGS

16.9: SETTINGS MENU

16.9: SETTINGS MENU

Set Meter In Point

Determine the metering point for the input channel level meters.

There are four choices for the input meter tap, from left to right: After the analogue mic gain (before digital trim
and filters); after the digital trim and filters (before the Gate/EQ/Dynamics); after the Gate/EQ/Dynamics (before
the fader); after the fader.

Graphic EQ Large/Small Mode

Choose between Large and Small Graphic EQ control modes.

Choose ‘Large’ 30-fader mode for fast access on multiple faders, at the expense of access to the input faders, or
choose ‘Small’ (eight output faders) mode when access to input faders must be retained at all times. Frequency
bands can be scrolled in banks of four or eight bands, using the Output Fader page buttons.

Set Delay Units

Change the units used in input, output, and monitoring delay adjustments.

You can choose between milliseconds, metres, or feet and inches.

EQ bandwidth units

Choose the unit for bandwidth controls in the EQ sections throughout the console

Selected either Octaves or Q-factor (defined as the ratio of frequency to bandwidth). The direction of the control
is reversed between the two settings: In Q mode, clockwise narrows bandwidth, in Octaves mode, clockwise
widens bandwidth.

Enable NEXT and LAST

Enable the [NEXT] and [LAST] cue list navigation buttons nearest the operator.

DSP Configuration

Set the console’s DSP sample rate.

You can choose 48kHz (128 input channels) or 96kHz (64 input channels). Press {SET} to confirm a change.
NOTE: Changing the sample rate will reset the console and you will lose unsaved changes. A warning/confirma-
tion dialogue appears.

«
...
167
168
169
170
171
...
»

Содержание Vi5000


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vi5000

Бренд: Panasonic Страницы: 37

Бренд: Panasonic Страницы: 2

Бренд: Hagerman Страницы: 9

Бренд: Hagerman Страницы: 4

DD-7 Digital Delay

Бренд: Boss Страницы: 32

Бренд: DAPAudio Страницы: 16

Бренд: SPACE POST ELECTRONICS Страницы: 5

Бренд: Cimo Страницы: 9

Бренд: Zero88 Страницы: 65

Бренд: TZS First AUSTRIA Страницы: 16

Бренд: Sinbo Страницы: 41

Бренд: Soba Страницы: 16

Бренд: Rolls Страницы: 1

Бренд: Rolls Страницы: 4

Бренд: Pro Co Sound Страницы: 2

Бренд: Dunlop Страницы: 2

Бренд: Nordic Home Culture Страницы: 42

Бренд: Tascam Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды