SoundCraft Vi5000 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 225

SoundCraft Vi5000 Скачать руководство пользователя страница 142

Vi5000/7000 User Manual

15.1: TBACK & OSC CONTROLS

®

15.1: TALKBACK & OSCILLATOR CONTROLS

TALKBACK & OSCILLATOR > CONTROLS

Talkback And Oscillator Setup

Open and close the Talkback and Oscillator setup screen in the master Vistonics screen.

Talkback XLR Connector

The Talkback Mic input.

This connector is duplicated on the rear panel of the surface. There is a switch for phantom power adjacent to the
rear panel Talkback Mic connector if required.

Talkback / OSC Level Control

Control of Talkback or Oscillator level.

For Talkback, the analogue Mic Amp gain is variable from 46-66dB by 3 internal jumpers which are located on
the PCB that is located adjacent to the rear-panel talkback mic connector.. This is set by default to a mid-range
setting. If the Oscillator is active, the control adjusts the Osc level to all destinations. The level setting is stored
independently for TB and Osc. The front-panel Talkback/Osc level control applies an additional digital gain trim to
the talkback mic signal.

Talkback To Internal

Route the Talkback signal to pre-selected output busses.

The 'INT' routed Output busses are selected via their {TB} VST keys in the VST area of the master screen after
selecting the [TB ASSN] key (located to the right of the master screen’s VST area). Switch between the two sets
of 16 busses with the [PAGE A] and [PAGE B] keys.

«
...
140
141
142
143
144
...
»

Содержание Vi5000


































































































































































































































Отзывы:

Нет отзывов