SoundCraft Vi5000 страница 177 Скачать руководство пользователя

Страница: 177 / 225

Vi5000/7000 User Manual

17.1.1: TAP TEMPO

LEXICON FX > TAP TEMPO

17.1.1: FX > TAP TEMPO

17.1.1: FX > USING THE FX > TAP TEMPO

For each effect that offers TAP Tempo (Tempo synchronisation using key press), the bottom left key {TEMPO} is used

as the TAP button.

In live situations it is often advantageous to be able to easily control the TAP function from a button that is permanently

accessible on the console surface. The large F1-6 keys below the master screen are assigned by default on to the tap

function of FX1-6, so no further setup is needed as long as shows are built from the console’s internal default shows.

However if you are importing a show from a Vi 4 or 6 console, only the first two of these F keys may be mapped to the

tap function. The information that follows will allow any F key to be mapped to the tap function of any FX unit in the

event that a Vi4 or 6 show is being used.

In order to assign the TAP functions of FX units to the F-keys, proceed as follows (refer to the screenshot above):

. Press the MENU button and select the {GPIO} menu tab.

. Ensure the {LOCAL I/O} button is selected and scroll the input and output sections down to the VGPI and VGPO Pin

settings. For LEX3, select VGPI Lex Tap3 and VGPO Lex Tap3.

. Set the parameters for the VGPI and VGPO as shown in the above picture, and ensure the input and output are

switched ON.

Use a similar procedure for other FX units.

NOTE: Normal F-Key setup functions will be over-ridden when an FX unit with Tap-Tempo function is selected in the

corresponding FX unit. That is, if F1 is setup as a short-cut to a screen, the default tap-tempo VGPIO tap function for

FX unit 1 will be active when FX1 has a delay selected.

Tap Tempo Functionality

Содержание Vi5000


































































































































































































































Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды

SoundCraft Vi5000, Руководство пользователя

Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды